1980s Retro Toyota “T” badges
These are Retro Toyota “T” logos inspired from Toyota logos used in the early 80s. Instead of chrome plastic we went with a more modern brushed aluminum. There are 2 versions. Version #1 is a bit larger at 4″ tall by 3 1/4″ wide. Versioni #2 is 3 3/8″ x 3 1/4″ wide. These are a bit larger than the original OEM badges. They both come with 2 strips of 3M automotive adhesive on back in case you want to stick it on. They will mount to any flat surface on our vehicle. They also come with screws and washers and pre-existing threaded holes in case you want to attach with screws. You do NOT need to use both forms of attachment.
3rd Gen 4Runner Rear Cargo Accessories Panel (99-02)
This is a rear cargo area accessories plate that replaces the OEM 12 volt accessory panel found on the 99-02 4Runner. This can be mounted to the 96-98 4Runner but the hole will need to be cut and a new 12VDC 10A power supply will need to be ran. This plate is made from ABS plastic by a 3D printer. There are two versions available. There is design #1 which has 2 accessory 12 volt holes/plugs, 1 OEM window switch hole (window switch not included), and one 12 volt meter display. There is also design #2 which has 3 12 volt accessory holes (no window switch hole), and a 12 volt meter. Please be aware the top right corner MUST be the 12 volt meter due to the shallow design of that accessory. Behind the plastic interior wall is a metal plate in that location and a full depth 12 volt accessory plug will not fit. The other 3 accessory locations do not have anything behind it and any 1″ accessory plug can be mounted there. You can order this as the plate only OR fully set up with all accessory plugs pre-installed with connectors and a spool of wire. Running and connecting wiring is done by the customer.
Ashtray 40 Series 81-84+
This is an ashtray for the rear ashtray hole on the 1981-1984 40 Series Landcruiser center console. This is designed to look very similar to the OEM design but not identical. The original OEM design had numerous structural issues leading to cracking in numerous places. Those structural issues have been addressed in this design. It will still fit, look, and function like the OEM design. The hinge hardware has also been reinforced to be much more robust then the OEM slide pegs that were originally used. There are pressed fit and hidden nuts under the hinge with countersunk hardened black bolts. The original OEM metal plate spring is NOT included with this cup holder. The updated hardware gives the lid a stiffer movement which removes the need for the metal plate spring. The recessed area is still in this design to accept the OEM plate spring if you decide you want the look of it. This is made of ABS plastic with a black satin finish.
3rd Gen 4Runner Console Accessory Plate
This is an accessories panel for the 1996-2002 Toyota 4Runner. It mounts to the center console. This is made by a 3D printer from ABS plastic. This will accept OEM Toyota switches from 95-02 and some aftermarket switches. There are two options which is the 4 hole plate and the 2 holes plate. Install instructions will be provided with the packaging. Blank plug inserts can be ordered separately if you want 4 holes but only have 2 accessories so far and don’t want to have an ugly hole for a time period.
70 Series Cup Holder-Go to Odd Iron Offroad For Purchasing-Link Below
Now sold at our vendor site at http://www.oddironoffroad.com/store#!/70-Series-Cup-Holders-by-BH3D/p/82522362/category=23176020
This is a double cup holder for the 70 series landcruiser. This cup holder has a slot for 2 drinks, 2 pens, a cell phone, and a slot for a multi-tool or knife. It comes in a flat black finish. There are two versions. Both designs will work on either the RHD or LHD variants. Both have the some shape/functions up top but mount very differently. One cup holder is for the 70 series that came with a center console that goes up and around the shifters. It will mount up on top of the consoles and will come with 6 strips of 3M adhesive to secure it. It also has screw holes that will line up with the factory screw holes if you want to screw it down. You will need to source the screw. This cup holder can be flipped 180 degrees to go on either the RHD or LHD. The other double cup holder mounts to the floor of the 70 series landcruiser. It will also come with strips of 3M adhesive. That alone with not be adequate for attachment. You will need to screw the floor mounted cup holder into the floor. 2 self taping screws will be provided for that model. There are two countersunk holes at the bottom of this cup holder to guide you in placement of the screws. These cup holders are 3D printed and made of ABS plastic. I can do certain custom colors upon request. I have color matches in brown and gray for certain years/models 70 series but not all.
Aluminum FJ Cruiser TEQ Badge
This is a brushed aluminum TEQ badge that can be mounted on all years FJ Cruisers and can be mounted in numerous locations on the upper and lower grille. The backing plate is installed from the rear of the grille. Provided strips of 3m automotive adhesive are already installed on the back of the emblem. You simply need to remove the red backing from the tape and stick the emblem onto the backing plate. Use good force when installing the adhesive. The install should take 1-2 minutes tops. No tools are needed. This adhesive is VERY sticky so make sure you line it up and get it straight before you stick it on. You probably want someone to hold the backing plate in place while you install the TEQ badge so you can be directly in front and level with the badge as you install it to guarantee you get it straight. I have the black/silver, red/silver, and bare aluminum in stock. The bare aluminum would be for the folks looking to color match their paint.
3FE “EFI” engine badge
This is a replacement 3FE “EFI” engine badge. It is made of aluminum with a brushed finish and red letters. The letters are painted with high heat fully cured engine enamel. There are 3 options. You can order the engine badge by itself without the high heat adhesive if you already have some at home. You can order the badge WITH a tube of the high heat adhesive. The final option is the EFI FJ40 grille badge (coming soon).
1979-1980+ 40 Series Double Cup Holder
This is a double cup holder for a 1979-1980+ FJ40 Toyota Landcruiser. This console was also offered in years after 1980 in FJ40s without the rear heat. This is made of ABS plastic from a 3D printer. It will come in a smooth flat black finish. This double cup holder has holes of 3.25″ to allow for large drinks containers and the 30/40 oz. yeti type thermos. This cup holder will hold two cups, two pens, and a cell phone. It will come with strips of 3M automotive adhesive under the cup holder in case you want to permanently attach it to the console but that is not required for install. No hardware needed.
2011-2015 Tacoma TEQ Grille Badge
This aluminum TEQ badge mounts onto the front grille of your 2011-2015 Toyota Tacoma. It replaces OEM part #90975-A2001. The size is 6.25″ x 4.25″ (159mm x 108mm) The factory chrome badge must be removed. The factory mounting holes will not be used on the new badge. To remove the factory badge simply pry it off. It is held on with plastic tabs. No adhesive or screws were used. The new badge is held on with 3M automotive decal adhesive. The surface on the grille the new badge will mount to MUST be cleaned before mounting. This badge comes in the common black/silver color, red/silver color, and in raw metal (no paint or primer) for folks who want to do their own custom paint job.
Universal 2oz. Hand Sanitizer Holder
This is a 3D printed 2oz. Hand Sanitizer bottle holder. It is made from ABS plastic. It will hold most major brands of 2oz. hand sanitizer bottles. It comes with 3 strips of 3M automotive adhesive. Some of the brands it holds are shown in picture 5 but there are more. This holder can be stuck to any flat surface in your car, shop, work space, garage, kitchen, etc. Make sure the surface you stick it to has been thoroughly cleaned first. You can order this holder with 1, 2, or 3 bottles of hand sanitizer.
Toyota Pickup (1984-1988) Single Cup Holder
Be aware that there are 4 different consoles that came on the pickup and this insert will only fit one of them. Make sure to look at the pics closely to make sure they match your console. This is a single cup holder for the 84-88 Toyota Pickup. This is made of ABS plastic by a 3D printer. It has a 3″ diameter hole which will hold most beverage containers on the market. There are also two holes to accept pens and a small storage compartment in the back for whatever you can stick in there. There are 2 strips of 3M automotive adhesive on the bottom if you want to glue it into place. This comes in a satin black finish only.
Hilux Surf Double Cup Holder 1996-2002
This is a 3D printed double cup holder for the 1996-2002 Toyota Hilux Surf. This will work on the 4WD automatic console. This will NOT fit on the manual transmission console. That design in still in development. This cup holder is made of ABS plastic and comes in flat black only. This design one large hole with removable snap ring, one smaller hole, and a cell phone slot . The large hole with snap ring removed can accept the newest 36oz. Yeti bottle. With the snap ring in place the cup holder will hold a Nalgene and 32/40oz. Hydroflask. The smaller standard 3″ hole will accept most fast food style containers. This design will hold just about any container on the market. Be aware, this design prevents full forward movement of the passenger seat. The front 3″ of movement will be blocked by the cup holder.
Install Instructions
There are 2 strips of 3M automotive adhesive already attached to help with install. Make sure the surface attaching to is totally clean. Once stuck in place with the adhesive then you will want to use the 2 provided self-taping screws in the side and top hole. Use a hand screw driver and not a power drill so you don’t strip the hole.
70 Series Landcruiser Turbo Grille badge
This is a machined aluminum “Turbo” badge that mounts to the 70 Series Landcruiser grille. This does NOT fit on all years 70 series cruisers. Please look closely at the pics to ensure the picture matches your grille. This is attached with 3M badge/decal foam adhesive. No screws are needed and no modifications to the factory grille are needed.
1st Gen 4Runner Cup Holder (Driver Side)
This is a single cup holder that mounts onto the driver side of the console. It is a standard 3″ diameter hole which will hold the usual fast food cup, soda can, and grocery store water bottle. It will not hold the larger Hydroflasks, Yeti’s, and Nalgene bottles. Our passenger cup holder can do that. The driver side cup holder had to be smaller to account for the drivers leg and shifter levers. This attaches with 2 strips of 3M adhesive and 2 self tapping screws. It is made of ABS plastic with a 3D printer.
Cup Holder Ashtray Insert 40 Series 81-84
This is a cup holder that inserts into the ashtray slot on the 1981-1984 Toyota Landcruiser 40 Series. This mounts to the center console and you must have the center console for this to work. It has a 3.25″ top diameter which will accept a majority of drink containers on the market. It also has a small storage cubby at the bottom for loose change or whatever else you want to store in there. This is made of ABS plastic with a satin black finish.
Aluminum Retro “4 Wheel Drive Badge”
This is a machined aluminum retro Toyota “4 Wheel Drive” badge. It can be mounted on any flat surface of any Toyota 4×4. It is roughly 4.5″ x 3″ which is the same size as the original Toyota badge. There are 3 color options available. There is the black/silver, cream/silver, and bare aluminum. The black is a satin finish while the cream is a gloss finish. The gloss allowed the cream to stand out a bit more. The bare aluminum is for the folks that want a custom color and are willing to paint themselves. I can also do custom color combos for a couple extra dollars if you let me know what you want. Just send a message regarding your request. These come with 3 strips of 3M automotive adhesive recessed on the backside and ready to install. Make sure the surface you are sticking to if flat and clean.
1979-1980+ 40 Series Single Cup Holder
This is a single cup holder for a 1979-1980+ FJ40 Toyota Landcruiser. This console was also offered in years after 1980 in FJ40s without the rear heat. This is made of ABS plastic from a 3D printer. It will come in a smooth flat black finish. This single cup holder has a hole of 3.25″ to allow for large drinks containers and the 30/40 oz. yeti type thermos. This cup holder will hold one cup, two pens, and a cell phone. It will come with strips of 3M automotive adhesive under the cup holder in case you want to permanently attach it to the console but that is not required for install. No hardware needed.
Universal Turbo Badge
This is an aluminum retro “Turbo” badge. This is inspired by the “Turbo” badge Toyota made in the 1980s. It can mount to any flat surface on the vehicle. Will come with 1-2 strips (depending on size) of 3M automotive adhesive to mount to the vehicle. There are 2 sizes and two color options for each size for a total of 4 options. There is the 7″ and 5″ black/silver badges. There is also the 7″ and 5″ black/silver/red badges.
TOYOTA Aluminum Universal Badge
This is a 8″x2″ machined aluminum TOYOTA retro badge. It was made to closely resemble the TOYOTA logo found on FJ40’s and other early Toyota trucks and SUVs. It has 3 recessed slots on the back for 3 long strips of 3M automotive adhesive. It will stick flush to any flat surface on any Toyota truck or SUV. It is available in black, red, and cream. The letters will have a brushed aluminum finish. More pictures are coming soon of the other colors.
89-94 Toyota Pickup Console Cup Holder
This will fit in the 1989-1994 Toyota pickup console. This was mostly offered in the SR5 model. This is 3D printed from ABS plastic. No hardware or tools are needed to install. This will NOT fit in the 4Runner from the same years. That is a different console and we make a different cup holder for the 4Runner console.
BH3D T-Shirt
These t-shirts are made of a very soft durable cotton from Next Level Apparel. They come in a gun metal gray color. It tends to run as a slight “slim” fit meaning it’s a little bit more snug in the shoulders and arms. They are a good long length for men but run a little snug. If you like a loose fitting shirt then I would say order one size up from what you normally where.
Aluminum Tacoma Grille Badge 2001-2004
This is a 2 piece aluminum TEQ grille badge for the 2001-2004 Toyota Tacoma. The outer visible piece is made from machined aluminum. The backing plate that goes behind the grille and protrudes forward to the front is made of 3D printed ABS plastic. Look at the pictures to fully understand the 2 piece design. This comes in two options; there is the satin black and gloss red finish. You can also order in bare aluminum and add your own color option. There are no tools needed and no hardware used. The factory badge must be removed first and then the backing plate will slide in behind the grille opening. You do not need to remove the grille to do this. Just pop the hood for easy access. The TEQ badge will have 3M adhesive on the backside. Remove the red backing tape from the adhesive and simply stick the badge onto the backing plate sandwiching the grille in between. Use good force while clamping and hold there for 20 seconds to ensure a good bond.
Aluminum TEQ Universal Badge (Round and Oval)
These are machined Aluminum TEQ badges (NOT PLASTIC) that can be mounted to any year and model Toyota/Lexus on any flat surface. It comes in 2 options. You can order the round or oval TEQ badge. Each badge comes in 3 finishes. You can get the red/silver, black/silver, and bare metal. The black/silver has a satin finish. The red/silver has a gloss finish. Just seemed to look best in those two finishes for those specific colors. The bare metal is for folks who want to paint them with your own custom color. Just do a couple heavy coats and then give 48 hours of drying time. Get some fine grit sandpaper and sand off the outer edge exposing the aluminum on the letters. The round is 3.5″ in diameter. The oval is 3.5″ tall and 5.2″ wide. These come with 3 strips of 3M automotive adhesive already installed. When installing make sure the surface is clean. Make sure you take your time to get it right. Once it’s stuck on, it does NOT want to come off.
Universal Diesel/TEQ badge
This is a Universal Aluminum TEQ/Diesel badge for a Toyota. The lettering is inspired by the Diesel font used by Toyota throughout the early 80s to late 90s. This is designed to mount on any flat smooth surface on the vehicle. It comes with strips of 3M automotive adhesive on back for attachment.