3rd Gen 4Runner (96-02) Rear Hatch TEQ Badge
This is an aluminum rear hatch TEQ badge that will replace the factory Toyota logo. This will fit on the rear hatch of any 1996-2002 Toyota 4Runner. It matches the subtle curvature of the rear hatch of the 3rd Gen 4Runner specifically. This badge comes in black or red with a brushed aluminum raised trim. It will come with 2 recessed strips of 3M automotive decal adhesive for install. Make sure the surface is clean when installing. To remove the old factory badge you need something like a butter knife or flat head screw driver to pry it off. There are two plastic tabs that help center the factory badge that need to be fully pulled out. The glue should be off with medium force. If it does not, a blow drier or heat gun can heat it up and soften it and make removal a bit easier.
70 Series Cruiser Diesel Grille Badge
This is an aluminum diesel badge. It comes it two options. You can order the grille badge that comes with a backing plate pre-attached to allow it to mount flush to the curvature on the grille of the 70 Series Landcruiser OR you can order it without the backing plate as a flat universal mount badge that can be mounted to any flat surface on the vehicle. It has a satin black finish with brushed aluminum raised letters. The OEM screw pegs are not present on our badge so that the badge can mount to 70 series grilles that did NOT come with the holes for mounting. Our badge mounts with 3M automotive badge adhesive. It’s plenty strong to hold the badge for many years without issue as long as the surface is thoroughly cleaned before install. No drilling of the factory grille is needed. Simply peel back the glue backing and stick it on.
1st Gen 4Runner Cup Holder (Driver Side)
This is a single cup holder that mounts onto the driver side of the console. It is a standard 3″ diameter hole which will hold the usual fast food cup, soda can, and grocery store water bottle. It will not hold the larger Hydroflasks, Yeti’s, and Nalgene bottles. Our passenger cup holder can do that. The driver side cup holder had to be smaller to account for the drivers leg and shifter levers. This attaches with 2 strips of 3M adhesive and 2 self tapping screws. It is made of ABS plastic with a 3D printer.
1980s Retro Toyota “T” badges
These are Retro Toyota “T” logos inspired from Toyota logos used in the early 80s. Instead of chrome plastic we went with a more modern brushed aluminum. There are 2 versions. Version #1 is a bit larger at 4″ tall by 3 1/4″ wide. Versioni #2 is 3 3/8″ x 3 1/4″ wide. These are a bit larger than the original OEM badges. They both come with 2 strips of 3M automotive adhesive on back in case you want to stick it on. They will mount to any flat surface on our vehicle. They also come with screws and washers and pre-existing threaded holes in case you want to attach with screws. You do NOT need to use both forms of attachment.
3rd Gen 4Runner Mud Flap End Caps
This is for a PAIR of front mud flap end caps for the SR5 model Toyota 4Runner. This is designed to fill in the fender gap created when the factory running boards are removed from the 1996-1998 4Runner. These are made of ABS plastic from a 3D printer. They are sanded and smoothed to hide most of the 3D printing lines. They are printed in black then chemically smoothed for strength and appearance. A coat of black plastic primer with 3 coats of flat black paint over that is used. No hardware provided. Use the factory hardware that was used to attach the running boards to the fender flares.
3FE “EFI” engine badge
This is a replacement 3FE “EFI” engine badge. It is made of aluminum with a brushed finish and red letters. The letters are painted with high heat fully cured engine enamel. There are 3 options. You can order the engine badge by itself without the high heat adhesive if you already have some at home. You can order the badge WITH a tube of the high heat adhesive. The final option is the EFI FJ40 grille badge (coming soon).
Toyota Pickup (1984-1988) Single Cup Holder
Be aware that there are 4 different consoles that came on the pickup and this insert will only fit one of them. Make sure to look at the pics closely to make sure they match your console. This is a single cup holder for the 84-88 Toyota Pickup. This is made of ABS plastic by a 3D printer. It has a 3″ diameter hole which will hold most beverage containers on the market. There are also two holes to accept pens and a small storage compartment in the back for whatever you can stick in there. There are 2 strips of 3M automotive adhesive on the bottom if you want to glue it into place. This comes in a satin black finish only.
BH3D Hat (Free with purchase over $100)
This is a BH3D adjustable fit mesh back hat. It's a charcoal gray color. This hat is built Richardson and is their Type 112 hat built to last. If you spend over $100 on our website then the hat is free.
Use Coupon code “Free Hat” during checkout once you have added at least $100 of product into the cart. Also, make sure you actually add the hat into the cart first.
Universal Diesel/TEQ badge
This is a Universal Aluminum TEQ/Diesel badge for a Toyota. The lettering is inspired by the Diesel font used by Toyota throughout the early 80s to late 90s. This is designed to mount on any flat smooth surface on the vehicle. It comes with strips of 3M automotive adhesive on back for attachment.
BH3D T-Shirt
These t-shirts are made of a very soft durable cotton from Next Level Apparel. They come in a gun metal gray color. It tends to run as a slight “slim” fit meaning it’s a little bit more snug in the shoulders and arms. They are a good long length for men but run a little snug. If you like a loose fitting shirt then I would say order one size up from what you normally where.
Aluminum Tacoma Grille Badge 2001-2004
This is a 2 piece aluminum TEQ grille badge for the 2001-2004 Toyota Tacoma. The outer visible piece is made from machined aluminum. The backing plate that goes behind the grille and protrudes forward to the front is made of 3D printed ABS plastic. Look at the pictures to fully understand the 2 piece design. This comes in two options; there is the satin black and gloss red finish. You can also order in bare aluminum and add your own color option. There are no tools needed and no hardware used. The factory badge must be removed first and then the backing plate will slide in behind the grille opening. You do not need to remove the grille to do this. Just pop the hood for easy access. The TEQ badge will have 3M adhesive on the backside. Remove the red backing tape from the adhesive and simply stick the badge onto the backing plate sandwiching the grille in between. Use good force while clamping and hold there for 20 seconds to ensure a good bond.
Universal Turbo Badge
This is an aluminum retro “Turbo” badge. This is inspired by the “Turbo” badge Toyota made in the 1980s. It can mount to any flat surface on the vehicle. Will come with 1-2 strips (depending on size) of 3M automotive adhesive to mount to the vehicle. There are 2 sizes and two color options for each size for a total of 4 options. There is the 7″ and 5″ black/silver badges. There is also the 7″ and 5″ black/silver/red badges.
TOYOTA Aluminum Universal Badge
This is a 8″x2″ machined aluminum TOYOTA retro badge. It was made to closely resemble the TOYOTA logo found on FJ40’s and other early Toyota trucks and SUVs. It has 3 recessed slots on the back for 3 long strips of 3M automotive adhesive. It will stick flush to any flat surface on any Toyota truck or SUV. It is available in black, red, and cream. The letters will have a brushed aluminum finish. More pictures are coming soon of the other colors.
Aluminum TEQ Universal Badge (Round and Oval)
These are machined Aluminum TEQ badges (NOT PLASTIC) that can be mounted to any year and model Toyota/Lexus on any flat surface. It comes in 2 options. You can order the round or oval TEQ badge. Each badge comes in 3 finishes. You can get the red/silver, black/silver, and bare metal. The black/silver has a satin finish. The red/silver has a gloss finish. Just seemed to look best in those two finishes for those specific colors. The bare metal is for folks who want to paint them with your own custom color. Just do a couple heavy coats and then give 48 hours of drying time. Get some fine grit sandpaper and sand off the outer edge exposing the aluminum on the letters. The round is 3.5″ in diameter. The oval is 3.5″ tall and 5.2″ wide. These come with 3 strips of 3M automotive adhesive already installed. When installing make sure the surface is clean. Make sure you take your time to get it right. Once it’s stuck on, it does NOT want to come off.
Aluminum Retro “4 Wheel Drive Badge”
This is a machined aluminum retro Toyota “4 Wheel Drive” badge. It can be mounted on any flat surface of any Toyota 4×4. It is roughly 4.5″ x 3″ which is the same size as the original Toyota badge. There are 3 color options available. There is the black/silver, cream/silver, and bare aluminum. The black is a satin finish while the cream is a gloss finish. The gloss allowed the cream to stand out a bit more. The bare aluminum is for the folks that want a custom color and are willing to paint themselves. I can also do custom color combos for a couple extra dollars if you let me know what you want. Just send a message regarding your request. These come with 3 strips of 3M automotive adhesive recessed on the backside and ready to install. Make sure the surface you are sticking to if flat and clean.
1995-2004 Tacoma Double Cup Holder
This is a double cup holder for the 1995-2004 Toyota Tacoma. There are two versions. One is for the 2WD and 4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder will hold two drinks, a cell phone, flashlight, and 2 pens. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength if you are adding two large drinks. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.
1995-2004 Tacoma Single Cup holder
This is a single cup holder for the 1996-2004 Toyota Tacoma. There are two versions. One is for the 2WD/4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder allows for full movement of the passenger seat into the forward position. This cup holder will hold one drink, a flashlight, and 1 pen. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.
Universal Diesel/TEQ badge
This is a Universal Aluminum TEQ/Diesel badge for a Toyota. The lettering is inspired by the Diesel font used by Toyota throughout the early 80s to late 90s. This is designed to mount on any flat smooth surface on the vehicle. It comes with strips of 3M automotive adhesive on back for attachment.
Universal Turbo Badge
This is an aluminum retro “Turbo” badge. This is inspired by the “Turbo” badge Toyota made in the 1980s. It can mount to any flat surface on the vehicle. Will come with 1-2 strips (depending on size) of 3M automotive adhesive to mount to the vehicle. There are 2 sizes and two color options for each size for a total of 4 options. There is the 7″ and 5″ black/silver badges. There is also the 7″ and 5″ black/silver/red badges.
200 Series Double Cup Holder
This is a complete drop in cup holder replacement. The OEM cup holder and lid needs to be removed completely for this to be inserted. This is made in ABS plastic with a flat textured black finish. There are 2 versions for the Cruiser and LX570. Version 1 has one large hole with removable snap ring, one smaller hole, and a cell phone slot . The large hole with snap ring removed can accept the newest 36oz. Yeti bottle. With the snap ring in place the cup holder will hold a Nalgene and 32/40oz. Hydroflask. The smaller standard 3″ hole will accept most fast food style containers. Version 2 has two large holes with 2 removable snap rings. This option can hold 2 of the large containers like a 32/40oz. Hydroflask, Yeti bottles, and Nalgene bottle but can not hold a cell phone due to space issues. There are strips of 3M adhesive on the bottom of the new cup holder but is not necessary for install. The cup holder is stable without the adhesive but provided in case the installer wants something extremely secure. To remove the OEM cup holder just open the lid and pull upward with about 10lbs of force. The OEM cup holder simply snaps into the hole with no use of hardware or adhesive. You may want to tap the cup holder with the handle of a screw driver as you pull to help dislodge.
BH3D Hat (Free with purchase over $100)
This is a BH3D adjustable fit mesh back hat. It’s a charcoal gray color. This hat is built Richardson and is their Type 112 hat built to last. If you spend over $100 on our website then the hat is free.
Use Coupon code “Free Hat” during checkout once you have added at least $100 of product into the cart. Also, make sure you actually add the hat into the cart first.
200 Series/LX570 Cup Holder Inserts
This is a 3D printed cup holder insert that goes inside of the OEM recessed cup holder hole of the 200 Series Landcrusier and the Lexus LX570. These are 3″ diameter holes allowing for a much more secure smaller hole than the OEM holes. This will fit most beverage containers out there but not all. If drinking from something large you can simply remove the insert for a larger hole. This is made of ABS plastic. There are 3 options. Option one is for the Landcruiser Console. This option allows for the lid to close. Option 2 is for the LX570 console. This option does NOT allow the lid to close. It is the same depth as the Landcruiser insert but since the LX570 console is more shallow, you can’t close the lid. Option 3 is is also for the LX570 console but it DOES allow the lid to close. This option follows the curvature of the lid so it can close but it is more shallow. No screws, adhesive, or hardware of any kind is used. Simply insert and your done.
2nd Gen 4Runner Double Cup Holder Console Insert
This is a double cup holder for the 2nd gen 4Runner from 1990-1995. It comes with a cell phone slot, 2 cup holders, and 2 pen holders. These are made of ABS plastic from a 3D printer. This mounts inside of the upper storage console. They will come in a black flat finish only. The cup holder will come with 2 strips of 3M automotive adhesive along the bottom if you want to permanently secure it into place but this is not a must. This cup holder will allow the lid to fully close when there are not cups, pens, or phones in it.
2nd Gen 4Runner Cup Holder Console Insert
This is a single cup holder for the 90-95 Toyota 4Runner. This is made of ABS plastic by a 3D printer. It has a 3″ diameter hole which will hold most beverage containers on the market. It also has a cell phone holder slot on the back that is 3.5″ wide which will accept just about every major phone style available. There are also two round holes to accept pens and two rectangular holes to accept a knife, leatherman, lighter, etc. There are also 2 strips of 3M automotive adhesive on the bottom if you want to glue it into place. This comes in a satin black finish only.