200 Series Double Cup Holder
This is a complete drop in cup holder replacement. The OEM cup holder and lid needs to be removed completely for this to be inserted. This is made in ABS plastic with a flat textured black finish. There are 2 versions for the Cruiser and LX570. Version 1 has one large hole with removable snap ring, one smaller hole, and a cell phone slot . The large hole with snap ring removed can accept the newest 36oz. Yeti bottle. With the snap ring in place the cup holder will hold a Nalgene and 32/40oz. Hydroflask. The smaller standard 3″ hole will accept most fast food style containers. Version 2 has two large holes with 2 removable snap rings. This option can hold 2 of the large containers like a 32/40oz. Hydroflask, Yeti bottles, and Nalgene bottle but can not hold a cell phone due to space issues. There are strips of 3M adhesive on the bottom of the new cup holder but is not necessary for install. The cup holder is stable without the adhesive but provided in case the installer wants something extremely secure. To remove the OEM cup holder just open the lid and pull upward with about 10lbs of force. The OEM cup holder simply snaps into the hole with no use of hardware or adhesive. You may want to tap the cup holder with the handle of a screw driver as you pull to help dislodge.
80 Series/LX450 Double Cup Holder
2nd Gen 4Runner Double Cup Holder
This is a double cup holder for the 1990-1995 Toyota 4Runner. It is made of ABS plastic. It will hold two cups, 2 cell phones, 2 pens, and a flashlight. The black insert gives you a 3″ diameter hole to hold a large variety of drinks. The smaller hole(closer to driver) is about 2 3/4″ which holds soda cans, water bottles, and medium sized drinks nice and snug. With the black insert removed you have a 3 3/4″ hole which holds a Nalgene sports bottle and other large bottles. This comes in the factory Tan, gray, golden brown, and satin black. This attaches with 2-4 self taping screws and strips of 3M automotive adhesive. The amount of screws varies between the 2WD, 4WD, and manual tranny cup holders due to the curvatures of each console and the screws needed to make it secure.
3rd Gen 4Runner Double CupHolder 96-02
This is a double cup holder for the 1996-2002 3rd gen Toyota 4Runner. It is made of ABS plastic and comes in the two factory colors which are tan “Oak” and the dark gray. This design is for the automatic 4WD and 2WD versions. It will NOT work on the manual transmission console. Our single cup holder design has an option for the manual tranny. The larger hole has an insert which holds large fast food cups. With the insert removed it can hold large water bottles like a Nalgene and Hydroflask bottle. The smaller cup holder can still hold large fast food type drinks snugly but can also securely hold small diameter containers like a soda can, small drink, and grocery store water bottles. There is also a cell phone slot on the passenger side that can handle almost all phones on the market. There are also two pen holders. This cup holder does NOT allow for full movement of the passenger seat. There is about 4″ of forward motion lost but the seat can still go back almost 6″ without issue. If full motion of the seat is extremely important to you then order the single cup holder which allow for that movement. Install Instructions There are 4 strips of 3m automotive adhesive already installed. Make SURE the console is cleaned really well before you attach and use good force when attaching. 2 screws are also included to be used in the 2 screw holes. The shorter silver screw goes underneath the black insert and the longer black screw goes in the lower side hole on the passenger side. Use a hand held screw driver to thread the screws in. Do not use a drill because you will probably strip the screw hole. Turn the screw until it is snug and then stop.
1981-1984+ 40 Series Double Cup Holder
This is a double cup holder for a 1981-1984+ FJ40 Toyota Landcruiser. This console was also offered in years after 1984 in some markets. This is made of ABS plastic from a 3D printer. It will come in a smooth flat black finish. This double cup holder has two different sized holes to accept all types of cups. This can hold the usual fastfood cup, coffee cups with handles, and even the large yeti 40oz cups with ease. The cup holder also has a slot for an LED flashlight, a slot for a knife/multi tool, and two pend slots. Along the one side there is room to hold two cell phones as well. This will come with 2 strips of 3M automotive adhesive on bottom in case you want to permanently attach it to the console but that is not required for install. No hardware or tools are needed for install.
200 Series/LX570 Cup Holder Inserts
This is a 3D printed cup holder insert that goes inside of the OEM recessed cup holder hole of the 200 Series Landcrusier and the Lexus LX570. These are 3″ diameter holes allowing for a much more secure smaller hole than the OEM holes. This will fit most beverage containers out there but not all. If drinking from something large you can simply remove the insert for a larger hole. This is made of ABS plastic. There are 3 options. Option one is for the Landcruiser Console. This option allows for the lid to close. Option 2 is for the LX570 console. This option does NOT allow the lid to close. It is the same depth as the Landcruiser insert but since the LX570 console is more shallow, you can’t close the lid. Option 3 is is also for the LX570 console but it DOES allow the lid to close. This option follows the curvature of the lid so it can close but it is more shallow. No screws, adhesive, or hardware of any kind is used. Simply insert and your done.
70 Series Cup Holder-Go to Odd Iron Offroad For Purchasing-Link Below
Now sold at our vendor site at http://www.oddironoffroad.com/store#!/70-Series-Cup-Holders-by-BH3D/p/82522362/category=23176020
This is a double cup holder for the 70 series landcruiser. This cup holder has a slot for 2 drinks, 2 pens, a cell phone, and a slot for a multi-tool or knife. It comes in a flat black finish. There are two versions. Both designs will work on either the RHD or LHD variants. Both have the some shape/functions up top but mount very differently. One cup holder is for the 70 series that came with a center console that goes up and around the shifters. It will mount up on top of the consoles and will come with 6 strips of 3M adhesive to secure it. It also has screw holes that will line up with the factory screw holes if you want to screw it down. You will need to source the screw. This cup holder can be flipped 180 degrees to go on either the RHD or LHD. The other double cup holder mounts to the floor of the 70 series landcruiser. It will also come with strips of 3M adhesive. That alone with not be adequate for attachment. You will need to screw the floor mounted cup holder into the floor. 2 self taping screws will be provided for that model. There are two countersunk holes at the bottom of this cup holder to guide you in placement of the screws. These cup holders are 3D printed and made of ABS plastic. I can do certain custom colors upon request. I have color matches in brown and gray for certain years/models 70 series but not all.
1995-2004 Tacoma Double Cup Holder
This is a double cup holder for the 1995-2004 Toyota Tacoma. There are two versions. One is for the 2WD and 4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder will hold two drinks, a cell phone, flashlight, and 2 pens. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength if you are adding two large drinks. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.
1995-2004 Tacoma Double Cup Holder
This is a double cup holder for the 1995-2004 Toyota Tacoma. There are two versions. One is for the 2WD and 4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder will hold two drinks, a cell phone, flashlight, and 2 pens. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength if you are adding two large drinks. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.
2nd Gen 4Runner Double Cup Holder Console Insert
This is a double cup holder for the 2nd gen 4Runner from 1990-1995. It comes with a cell phone slot, 2 cup holders, and 2 pen holders. These are made of ABS plastic from a 3D printer. This mounts inside of the upper storage console. They will come in a black flat finish only. The cup holder will come with 2 strips of 3M automotive adhesive along the bottom if you want to permanently secure it into place but this is not a must. This cup holder will allow the lid to fully close when there are not cups, pens, or phones in it.
60/62 Series Rear Double Cup Holder
This is a rear double cup holder made for the 1980-1990 60 and 62 Series Landcruiser. It is made of ABS plastic through the use of a 3D printer. The finish is a satin black that can be also used as a primer for the owner to do a custom OEM color match. It can hold most beverage containers on the market. The inside diameter of the holes is 3.25″ so anything inside that diameter will fit. There are also two holes for a pen/pencil. The rear sit WILL fold all the way down without issue but will make contact with the cup holder as it folds all the way down. The contact will not damage the cup holder. It comes with 4 strips of 3M automotive adhesive and 4 self tapping screws. The adhesive is strong but I would encourage you to use the screws as well. The adhesive will do a great job holding the cup holder in place while you attach the screws. Make sure the console is clean before you stick the cup holder down.
1979-1980+ 40 Series Double Cup Holder
This is a double cup holder for a 1979-1980+ FJ40 Toyota Landcruiser. This console was also offered in years after 1980 in FJ40s without the rear heat. This is made of ABS plastic from a 3D printer. It will come in a smooth flat black finish. This double cup holder has holes of 3.25″ to allow for large drinks containers and the 30/40 oz. yeti type thermos. This cup holder will hold two cups, two pens, and a cell phone. It will come with strips of 3M automotive adhesive under the cup holder in case you want to permanently attach it to the console but that is not required for install. No hardware needed.
60 Series Double Cup Holder
This is a double cup holder insert for the 60 Series Toyota Landcruiser. This cup holder is made of ABS plastic. It comes in a black satin finish. It will hold 2 cups, a cell phone, and 2 pens. There are strips of 3M adhesive installed on the bottom to stick it down into the hole. There are also 2 self taping screws provided. You can use the adhesive only or the adhesive and screws; depending on how secure you feel you need it.
1st Gen 4Runner Double Cup Holder
This is a double cup holder for the 1st gen 4Runner. Be aware that there are two very different options. One option is for the folks with the short center console with the larger storage tray. This is NOT for the short console with rear heat. This option is only for the non heat short console. It comes with a cell phone slot, 2 pen holders, and a multi-tool/knife holder. Option two is for the later model gen 1’s with the taller console with padded armrest. This storage tray is more narrow. This option does not have the cell phone slot or knife holder due to lack of space. It does still hold two pens. These are made of ABS plastic. They will come in an unpainted gloss black finish. The gloss finish is for durability and ease of cleaning. It can be painted any color if desired.
1973-1978 40 Series Double Cup Holder
This is a double cup holder insert for the stamped metal center console of a 1973-1978 Toyota Landcruiser. This is made of ABS plastic with a 3d printer. It will come with a smooth flat black finish. This cup holder has holes at 3.25″ diameter to accept large fast food cup type drinks and the 30/40 oz yeti type thermos. It will also hold smaller containers securely. This insert also has two slots for pens, a slot for a knife/multi-tool, a slot for an LED flashlight and still leave a 1.2″ slot in the rear for a cell phone or wallet. It will allow that awkward hole to have good functional use of the space. There will be 2 strips of 3M automotive adhesive on the bottom in case you want to permanently secure it to the bottom of the console. This is not needed for install. No hardware needed.
3rd Gen 4Runner Rear Double Cup Holder (1996-2002)
The is a rear double cup holder made for the 1996-2002 3rd Generation Toyota 4Runner. It is made of ABS plastic through the use of a 3D printer. It comes in the two factory colors of Tan and Gray. It can hold most beverage containers on the market. The inside diameter of the holes is 3″ so anything inside that diameter will fit. The flimsy factory rear cup holder will need to be removed first. There are two screws that hold the factory pull out cup holder in place. Once you pull it out you will be able to see and access them. Those 2 screws will not be reused. The new much stronger cup holder will come with 2 new longer screws. The cup holder should slide right into the hole left behind from the factory cup holder. You will need to apply force across the bottom to “click” the cup holder into place. Make SURE you here/feel the cup holder click into place. It has a locking tab underneath that will help secure it onto the console while you thread in the two screws. Remember that you are threading into plastic tabs and not metal. The screws can easily crack those tabs if you over tighten them. Get them snug and then stop turning. You can also use the 3M adhesive strip for added insurance but that is not a must.
Aluminum Tacoma Grille Badge 2001-2004
This is a 2 piece aluminum TEQ grille badge for the 2001-2004 Toyota Tacoma. The outer visible piece is made from machined aluminum. The backing plate that goes behind the grille and protrudes forward to the front is made of 3D printed ABS plastic. Look at the pictures to fully understand the 2 piece design. This comes in two options; there is the satin black and gloss red finish. You can also order in bare aluminum and add your own color option. There are no tools needed and no hardware used. The factory badge must be removed first and then the backing plate will slide in behind the grille opening. You do not need to remove the grille to do this. Just pop the hood for easy access. The TEQ badge will have 3M adhesive on the backside. Remove the red backing tape from the adhesive and simply stick the badge onto the backing plate sandwiching the grille in between. Use good force while clamping and hold there for 20 seconds to ensure a good bond.
Aluminum FJ Cruiser TEQ Badge
This is a brushed aluminum TEQ badge that can be mounted on all years FJ Cruisers and can be mounted in numerous locations on the upper and lower grille. The backing plate is installed from the rear of the grille. Provided strips of 3m automotive adhesive are already installed on the back of the emblem. You simply need to remove the red backing from the tape and stick the emblem onto the backing plate. Use good force when installing the adhesive. The install should take 1-2 minutes tops. No tools are needed. This adhesive is VERY sticky so make sure you line it up and get it straight before you stick it on. You probably want someone to hold the backing plate in place while you install the TEQ badge so you can be directly in front and level with the badge as you install it to guarantee you get it straight. I have the black/silver, red/silver, and bare aluminum in stock. The bare aluminum would be for the folks looking to color match their paint.
2022 Landcruiser Rear TEQ Badge
This is a rear hatch machined aluminum TEQ badge for the 2022 Toyota Landcruiser (300 Series). The original factory badge will need to be removed. This badge is held on with small strips of 3M automotive badges adhesive. Make sure the suface you are bonding to is clean and you use good force when applying the badge. Hold it in place for 20 seconds to ensure a solid bond.
2011-2015 Tacoma TEQ Grille Badge
This aluminum TEQ badge mounts onto the front grille of your 2011-2015 Toyota Tacoma. It replaces OEM part #90975-A2001. The size is 6.25″ x 4.25″ (159mm x 108mm) The factory chrome badge must be removed. The factory mounting holes will not be used on the new badge. To remove the factory badge simply pry it off. It is held on with plastic tabs. No adhesive or screws were used. The new badge is held on with 3M automotive decal adhesive. The surface on the grille the new badge will mount to MUST be cleaned before mounting. This badge comes in the common black/silver color, red/silver color, and in raw metal (no paint or primer) for folks who want to do their own custom paint job.
TOYOTA Aluminum Universal Badge
This is a 8″x2″ machined aluminum TOYOTA retro badge. It was made to closely resemble the TOYOTA logo found on FJ40’s and other early Toyota trucks and SUVs. It has 3 recessed slots on the back for 3 long strips of 3M automotive adhesive. It will stick flush to any flat surface on any Toyota truck or SUV. It is available in black, red, and cream. The letters will have a brushed aluminum finish. More pictures are coming soon of the other colors.
3rd Gen TEQ Grille Badge
This is an aluminum grille badge for the 1996-2002 Toyota 4Runner. There are 3 different grille options under this product. There is the grille badge for the 96-98 grille, the 99-00 grille, and the 01-02 grille. They are very different in how they mount so be careful to order the correct one. The 96-98 and the 99-00 Grille badge will come with a backing plate that mounts to the grille surface and the aluminum badge will mount to the backing plate. No hardware is needed for the 96-98 and 99-00 grille badge. The 01-02 grille badge does not come with a backing plate but instead will come with 3 screws and washers to use the factory mounting holes. Make sure to use the provided washers with the screws. Those are used to set the depth correctly and allow the badge to sit totally flush to the grille. Make sure the grill emblem surface has been thoroughly cleaned before mounting any of the badges.
Aluminum Tacoma Grille Badge 2001-2004
This is a 2 piece aluminum TEQ grille badge for the 2001-2004 Toyota Tacoma. The outer visible piece is made from machined aluminum. The backing plate that goes behind the grille and protrudes forward to the front is made of 3D printed ABS plastic. Look at the pictures to fully understand the 2 piece design. This comes in two options; there is the satin black and gloss red finish. You can also order in bare aluminum and add your own color option. There are no tools needed and no hardware used. The factory badge must be removed first and then the backing plate will slide in behind the grille opening. You do not need to remove the grille to do this. Just pop the hood for easy access. The TEQ badge will have 3M adhesive on the backside. Remove the red backing tape from the adhesive and simply stick the badge onto the backing plate sandwiching the grille in between. Use good force while clamping and hold there for 20 seconds to ensure a good bond.