80 Series/LX450 Double Cup Holder
2nd Gen 4Runner Double Cup Holder
This is a double cup holder for the 1990-1995 Toyota 4Runner. It is made of ABS plastic. It will hold two cups, 2 cell phones, 2 pens, and a flashlight. The black insert gives you a 3″ diameter hole to hold a large variety of drinks. The smaller hole(closer to driver) is about 2 3/4″ which holds soda cans, water bottles, and medium sized drinks nice and snug. With the black insert removed you have a 3 3/4″ hole which holds a Nalgene sports bottle and other large bottles. This comes in the factory Tan, gray, golden brown, and satin black. This attaches with 2-4 self taping screws and strips of 3M automotive adhesive. The amount of screws varies between the 2WD, 4WD, and manual tranny cup holders due to the curvatures of each console and the screws needed to make it secure.
3rd Gen 4Runner Double CupHolder 96-02
This is a double cup holder for the 1996-2002 3rd gen Toyota 4Runner. It is made of ABS plastic and comes in the two factory colors which are tan “Oak” and the dark gray. This design is for the automatic 4WD and 2WD versions. It will NOT work on the manual transmission console. Our single cup holder design has an option for the manual tranny. The larger hole has an insert which holds large fast food cups. With the insert removed it can hold large water bottles like a Nalgene and Hydroflask bottle. The smaller cup holder can still hold large fast food type drinks snugly but can also securely hold small diameter containers like a soda can, small drink, and grocery store water bottles. There is also a cell phone slot on the passenger side that can handle almost all phones on the market. There are also two pen holders. This cup holder does NOT allow for full movement of the passenger seat. There is about 4″ of forward motion lost but the seat can still go back almost 6″ without issue. If full motion of the seat is extremely important to you then order the single cup holder which allow for that movement. Install Instructions There are 4 strips of 3m automotive adhesive already installed. Make SURE the console is cleaned really well before you attach and use good force when attaching. 2 screws are also included to be used in the 2 screw holes. The shorter silver screw goes underneath the black insert and the longer black screw goes in the lower side hole on the passenger side. Use a hand held screw driver to thread the screws in. Do not use a drill because you will probably strip the screw hole. Turn the screw until it is snug and then stop.
1995-2004 Tacoma Double Cup Holder
This is a double cup holder for the 1995-2004 Toyota Tacoma. There are two versions. One is for the 2WD and 4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder will hold two drinks, a cell phone, flashlight, and 2 pens. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength if you are adding two large drinks. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.
1995-2004 Tacoma Double Cup Holder
This is a double cup holder for the 1995-2004 Toyota Tacoma. There are two versions. One is for the 2WD and 4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder will hold two drinks, a cell phone, flashlight, and 2 pens. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength if you are adding two large drinks. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.
60 Series Double Cup Holder
This is a double cup holder insert for the 60 Series Toyota Landcruiser. This cup holder is made of ABS plastic. It comes in a black satin finish. It will hold 2 cups, a cell phone, and 2 pens. There are strips of 3M adhesive installed on the bottom to stick it down into the hole. There are also 2 self taping screws provided. You can use the adhesive only or the adhesive and screws; depending on how secure you feel you need it.
1st Gen 4Runner Double Cup Holder
This is a double cup holder for the 1st gen 4Runner. Be aware that there are two very different options. One option is for the folks with the short center console with the larger storage tray. This is NOT for the short console with rear heat. This option is only for the non heat short console. It comes with a cell phone slot, 2 pen holders, and a multi-tool/knife holder. Option two is for the later model gen 1’s with the taller console with padded armrest. This storage tray is more narrow. This option does not have the cell phone slot or knife holder due to lack of space. It does still hold two pens. These are made of ABS plastic. They will come in an unpainted gloss black finish. The gloss finish is for durability and ease of cleaning. It can be painted any color if desired.
3rd Gen 4Runner Rear Double Cup Holder (1996-2002)
The is a rear double cup holder made for the 1996-2002 3rd Generation Toyota 4Runner. It is made of ABS plastic through the use of a 3D printer. It comes in the two factory colors of Tan and Gray. It can hold most beverage containers on the market. The inside diameter of the holes is 3″ so anything inside that diameter will fit. The flimsy factory rear cup holder will need to be removed first. There are two screws that hold the factory pull out cup holder in place. Once you pull it out you will be able to see and access them. Those 2 screws will not be reused. The new much stronger cup holder will come with 2 new longer screws. The cup holder should slide right into the hole left behind from the factory cup holder. You will need to apply force across the bottom to “click” the cup holder into place. Make SURE you here/feel the cup holder click into place. It has a locking tab underneath that will help secure it onto the console while you thread in the two screws. Remember that you are threading into plastic tabs and not metal. The screws can easily crack those tabs if you over tighten them. Get them snug and then stop turning. You can also use the 3M adhesive strip for added insurance but that is not a must.
1st Gen 4runner Single Cup Holder
This is a cup holder for the 1st gen body 4runner. It is for the manual transmission set up ONLY. It will hold just about any fast food cup size drink with the insert installed. With the insert removed it can hold a large sports (Nalgene) bottle. There is also a pen holder and cell phone holder. The inside width of the cell phone slot is 3.25″ That should accept just about any cell phone on the market including the new IPhone6 plus. There are two avialable colors: the dark gray or black. Both colors come in a satin/flat finish. Installation: There are two strips of 3M automotive adhesive underneath the cup holder to aid in attachment. There are also 2 screw holes located at the bottom of the cell phone tray and on the bottom outer edge. Two self taping screws are provided. No drill bits or power tools are needed. Just thread the screws into the plastic with a handheld phillips screw driver. They will drill themselves into the plastic. Do NOT over tighten. You are threading into thin plastic. Thread the screws in until they are snug and stop.
3rd Gen 4Runner Single CupHolder 96-02
This is a single cup holder for the 3rd gen Toyota 4Runner. It is made of ABS plastic and comes in the two factory colors which are tan “Oak” and the dark gray. The cup holder will hold any fast food cup and most beverage container sizes. If you remove the black insert then you have a much larger diameter cup holder for items like a Nalgene bottle. The cell phone slot 3.25″ across and .65″ deep which will allow for most larger cell phones on the market with a case. There is also a pen holder. This single cup holder DOES allow for almost full movement of the passenger seat front to back. You lose about 1/2″ of forward movement which is very minimal. You could push the cup holder forward to allow for full movement of the seat but that would cause the larger fast food cups to come in contact with the dash but that is also minimal. This is available for the automatic and now manual trans. Install Instructions There are 3 strips of 3m automotive adhesive already installed. This is the primary method of attachment. Make SURE the console is cleaned really well before you attach and use good force when attaching. The cup holder will not bond well if the console is not clean. 2 screws are also included to be used in the 2 screw holes. The screws are an added insurance to ensure the cup holder is secure. I would highly encourage you to use the screws. Use a small drill bit and predrill the holes once the cup holder has been stuck into place. Then use a hand held screw driver to thread the screws in. Do not use a drill because you will probably strip the screw hole. Also, do not over tighten them by hand. Turn the screw until it is snug and then stop.
80 Series/LX450 Single Cup Holder
1st Gen 4runner Cup Holder Console Insert
This is a single cup holder for the 84-89 Toyota 4Runner. This is made of ABS plastic by a 3D printer. It has a 3″ diameter hole which will hold most beverage containers on the market. It also has a cell phone holder slot that is 3.5″ wide which will accept just about every major phone style available. There is a notch at the bottom of the cell phone slot to allow a charging cable to be ran up from the bottom. Be aware you will need to cut a hole in the bottom on the console to be able to run the cable. There are also two holes to accept pens and a small storage compartment in the back for whatever you can stick in there. There is a countersunk hole at the bottom in case you want to screw it in. That is not a must, just a preference. Any 3/4″- 1″ coarse thread screw will work. There are also 2 strips of 3M automotive adhesive on the bottom if you want to glue it into place. This comes in a satin black finish only. Be aware that there are 4 different consoles that came on the 1st gen 4Runner and this insert will only fit in two of them(which do seem to be the more popular options). Make sure to look at the pics to make sure they match your console.