80 Series/LX450 Double Cup Holder
2nd Gen 4Runner Double Cup Holder
This is a double cup holder for the 1990-1995 Toyota 4Runner. It is made of ABS plastic. It will hold two cups, 2 cell phones, 2 pens, and a flashlight. The black insert gives you a 3″ diameter hole to hold a large variety of drinks. The smaller hole(closer to driver) is about 2 3/4″ which holds soda cans, water bottles, and medium sized drinks nice and snug. With the black insert removed you have a 3 3/4″ hole which holds a Nalgene sports bottle and other large bottles. This comes in the factory Tan, gray, golden brown, and satin black. This attaches with 2-4 self taping screws and strips of 3M automotive adhesive. The amount of screws varies between the 2WD, 4WD, and manual tranny cup holders due to the curvatures of each console and the screws needed to make it secure.
3rd Gen 4Runner Double CupHolder 96-02
This is a double cup holder for the 1996-2002 3rd gen Toyota 4Runner. It is made of ABS plastic and comes in the two factory colors which are tan “Oak” and the dark gray. This design is for the automatic 4WD and 2WD versions. It will NOT work on the manual transmission console. Our single cup holder design has an option for the manual tranny. The larger hole has an insert which holds large fast food cups. With the insert removed it can hold large water bottles like a Nalgene and Hydroflask bottle. The smaller cup holder can still hold large fast food type drinks snugly but can also securely hold small diameter containers like a soda can, small drink, and grocery store water bottles. There is also a cell phone slot on the passenger side that can handle almost all phones on the market. There are also two pen holders. This cup holder does NOT allow for full movement of the passenger seat. There is about 4″ of forward motion lost but the seat can still go back almost 6″ without issue. If full motion of the seat is extremely important to you then order the single cup holder which allow for that movement. Install Instructions There are 4 strips of 3m automotive adhesive already installed. Make SURE the console is cleaned really well before you attach and use good force when attaching. 2 screws are also included to be used in the 2 screw holes. The shorter silver screw goes underneath the black insert and the longer black screw goes in the lower side hole on the passenger side. Use a hand held screw driver to thread the screws in. Do not use a drill because you will probably strip the screw hole. Turn the screw until it is snug and then stop.
1981-1984+ 40 Series Double Cup Holder
This is a double cup holder for a 1981-1984+ FJ40 Toyota Landcruiser. This console was also offered in years after 1984 in some markets. This is made of ABS plastic from a 3D printer. It will come in a smooth flat black finish. This double cup holder has two different sized holes to accept all types of cups. This can hold the usual fastfood cup, coffee cups with handles, and even the large yeti 40oz cups with ease. The cup holder also has a slot for an LED flashlight, a slot for a knife/multi tool, and two pend slots. Along the one side there is room to hold two cell phones as well. This will come with 2 strips of 3M automotive adhesive on bottom in case you want to permanently attach it to the console but that is not required for install. No hardware or tools are needed for install.
70 Series Cup Holder-Go to Odd Iron Offroad For Purchasing-Link Below
Now sold at our vendor site at http://www.oddironoffroad.com/store#!/70-Series-Cup-Holders-by-BH3D/p/82522362/category=23176020
This is a double cup holder for the 70 series landcruiser. This cup holder has a slot for 2 drinks, 2 pens, a cell phone, and a slot for a multi-tool or knife. It comes in a flat black finish. There are two versions. Both designs will work on either the RHD or LHD variants. Both have the some shape/functions up top but mount very differently. One cup holder is for the 70 series that came with a center console that goes up and around the shifters. It will mount up on top of the consoles and will come with 6 strips of 3M adhesive to secure it. It also has screw holes that will line up with the factory screw holes if you want to screw it down. You will need to source the screw. This cup holder can be flipped 180 degrees to go on either the RHD or LHD. The other double cup holder mounts to the floor of the 70 series landcruiser. It will also come with strips of 3M adhesive. That alone with not be adequate for attachment. You will need to screw the floor mounted cup holder into the floor. 2 self taping screws will be provided for that model. There are two countersunk holes at the bottom of this cup holder to guide you in placement of the screws. These cup holders are 3D printed and made of ABS plastic. I can do certain custom colors upon request. I have color matches in brown and gray for certain years/models 70 series but not all.
1995-2004 Tacoma Double Cup Holder
This is a double cup holder for the 1995-2004 Toyota Tacoma. There are two versions. One is for the 2WD and 4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder will hold two drinks, a cell phone, flashlight, and 2 pens. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength if you are adding two large drinks. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.
1995-2004 Tacoma Double Cup Holder
This is a double cup holder for the 1995-2004 Toyota Tacoma. There are two versions. One is for the 2WD and 4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder will hold two drinks, a cell phone, flashlight, and 2 pens. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength if you are adding two large drinks. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.
2nd Gen 4Runner Double Cup Holder Console Insert
This is a double cup holder for the 2nd gen 4Runner from 1990-1995. It comes with a cell phone slot, 2 cup holders, and 2 pen holders. These are made of ABS plastic from a 3D printer. This mounts inside of the upper storage console. They will come in a black flat finish only. The cup holder will come with 2 strips of 3M automotive adhesive along the bottom if you want to permanently secure it into place but this is not a must. This cup holder will allow the lid to fully close when there are not cups, pens, or phones in it.
1979-1980+ 40 Series Double Cup Holder
This is a double cup holder for a 1979-1980+ FJ40 Toyota Landcruiser. This console was also offered in years after 1980 in FJ40s without the rear heat. This is made of ABS plastic from a 3D printer. It will come in a smooth flat black finish. This double cup holder has holes of 3.25″ to allow for large drinks containers and the 30/40 oz. yeti type thermos. This cup holder will hold two cups, two pens, and a cell phone. It will come with strips of 3M automotive adhesive under the cup holder in case you want to permanently attach it to the console but that is not required for install. No hardware needed.
60 Series Double Cup Holder
This is a double cup holder insert for the 60 Series Toyota Landcruiser. This cup holder is made of ABS plastic. It comes in a black satin finish. It will hold 2 cups, a cell phone, and 2 pens. There are strips of 3M adhesive installed on the bottom to stick it down into the hole. There are also 2 self taping screws provided. You can use the adhesive only or the adhesive and screws; depending on how secure you feel you need it.
1st Gen 4Runner Double Cup Holder
This is a double cup holder for the 1st gen 4Runner. Be aware that there are two very different options. One option is for the folks with the short center console with the larger storage tray. This is NOT for the short console with rear heat. This option is only for the non heat short console. It comes with a cell phone slot, 2 pen holders, and a multi-tool/knife holder. Option two is for the later model gen 1’s with the taller console with padded armrest. This storage tray is more narrow. This option does not have the cell phone slot or knife holder due to lack of space. It does still hold two pens. These are made of ABS plastic. They will come in an unpainted gloss black finish. The gloss finish is for durability and ease of cleaning. It can be painted any color if desired.
1973-1978 40 Series Double Cup Holder
This is a double cup holder insert for the stamped metal center console of a 1973-1978 Toyota Landcruiser. This is made of ABS plastic with a 3d printer. It will come with a smooth flat black finish. This cup holder has holes at 3.25″ diameter to accept large fast food cup type drinks and the 30/40 oz yeti type thermos. It will also hold smaller containers securely. This insert also has two slots for pens, a slot for a knife/multi-tool, a slot for an LED flashlight and still leave a 1.2″ slot in the rear for a cell phone or wallet. It will allow that awkward hole to have good functional use of the space. There will be 2 strips of 3M automotive adhesive on the bottom in case you want to permanently secure it to the bottom of the console. This is not needed for install. No hardware needed.
3rd Gen 4Runner Rear Double Cup Holder (1996-2002)
The is a rear double cup holder made for the 1996-2002 3rd Generation Toyota 4Runner. It is made of ABS plastic through the use of a 3D printer. It comes in the two factory colors of Tan and Gray. It can hold most beverage containers on the market. The inside diameter of the holes is 3″ so anything inside that diameter will fit. The flimsy factory rear cup holder will need to be removed first. There are two screws that hold the factory pull out cup holder in place. Once you pull it out you will be able to see and access them. Those 2 screws will not be reused. The new much stronger cup holder will come with 2 new longer screws. The cup holder should slide right into the hole left behind from the factory cup holder. You will need to apply force across the bottom to “click” the cup holder into place. Make SURE you here/feel the cup holder click into place. It has a locking tab underneath that will help secure it onto the console while you thread in the two screws. Remember that you are threading into plastic tabs and not metal. The screws can easily crack those tabs if you over tighten them. Get them snug and then stop turning. You can also use the 3M adhesive strip for added insurance but that is not a must.