3rd Gen 4Runner Double CupHolder 96-02
This is a double cup holder for the 1996-2002 3rd gen Toyota 4Runner. It is made of ABS plastic and comes in the two factory colors which are tan “Oak” and the dark gray. This design is for the automatic 4WD and 2WD versions. It will NOT work on the manual transmission console. Our single cup holder design has an option for the manual tranny. The larger hole has an insert which holds large fast food cups. With the insert removed it can hold large water bottles like a Nalgene and Hydroflask bottle. The smaller cup holder can still hold large fast food type drinks snugly but can also securely hold small diameter containers like a soda can, small drink, and grocery store water bottles. There is also a cell phone slot on the passenger side that can handle almost all phones on the market. There are also two pen holders. This cup holder does NOT allow for full movement of the passenger seat. There is about 4″ of forward motion lost but the seat can still go back almost 6″ without issue. If full motion of the seat is extremely important to you then order the single cup holder which allow for that movement. Install Instructions There are 4 strips of 3m automotive adhesive already installed. Make SURE the console is cleaned really well before you attach and use good force when attaching. 2 screws are also included to be used in the 2 screw holes. The shorter silver screw goes underneath the black insert and the longer black screw goes in the lower side hole on the passenger side. Use a hand held screw driver to thread the screws in. Do not use a drill because you will probably strip the screw hole. Turn the screw until it is snug and then stop.
Aluminum TEQ Universal Badge (Round and Oval)
These are machined Aluminum TEQ badges (NOT PLASTIC) that can be mounted to any year and model Toyota/Lexus on any flat surface. It comes in 2 options. You can order the round or oval TEQ badge. Each badge comes in 3 finishes. You can get the red/silver, black/silver, and bare metal. The black/silver has a satin finish. The red/silver has a gloss finish. Just seemed to look best in those two finishes for those specific colors. The bare metal is for folks who want to paint them with your own custom color. Just do a couple heavy coats and then give 48 hours of drying time. Get some fine grit sandpaper and sand off the outer edge exposing the aluminum on the letters. The round is 3.5″ in diameter. The oval is 3.5″ tall and 5.2″ wide. These come with 3 strips of 3M automotive adhesive already installed. When installing make sure the surface is clean. Make sure you take your time to get it right. Once it’s stuck on, it does NOT want to come off.
Aluminum 5th Gen 4Runner TEQ Front and Rear Badges
These are machined aluminum TEQ badges for the front grill and rear hatch of the 2009-Present 5th Generation Toyota 4Runner. They come in 3 color options. There is the popular black/silver combo, the retro red/silver combo, and the bare metal for the folks who want to do their own color option. These mount with strips of 3m automotive adhesive on the backside. The factory badge can be removed without even lifting the hood. You simply need a butter knife to pry behind the factory badge and pop it off. There are 3 plastic tabs that hold it on. No screws or adhesive were used to mount the factory badge. My TEQ badge will mount right over the same surface the factory badge was mounted to. Make sure you clean the grill well before sticking the badge on. The rear badge is more difficult to remove. It was installed from the factory with adhesive which will put up a fight before letting go. Be patient with the removal. Good force will be needed to remove it. Also, make sure you line up the badges VERY carefully because once you stick them on they will NOT want to come off.
3rd Gen 4Runner Rear Double Cup Holder (1996-2002)
The is a rear double cup holder made for the 1996-2002 3rd Generation Toyota 4Runner. It is made of ABS plastic through the use of a 3D printer. It comes in the two factory colors of Tan and Gray. It can hold most beverage containers on the market. The inside diameter of the holes is 3″ so anything inside that diameter will fit. The flimsy factory rear cup holder will need to be removed first. There are two screws that hold the factory pull out cup holder in place. Once you pull it out you will be able to see and access them. Those 2 screws will not be reused. The new much stronger cup holder will come with 2 new longer screws. The cup holder should slide right into the hole left behind from the factory cup holder. You will need to apply force across the bottom to “click” the cup holder into place. Make SURE you here/feel the cup holder click into place. It has a locking tab underneath that will help secure it onto the console while you thread in the two screws. Remember that you are threading into plastic tabs and not metal. The screws can easily crack those tabs if you over tighten them. Get them snug and then stop turning. You can also use the 3M adhesive strip for added insurance but that is not a must.
3rd Gen 4Runner Mud Flap End Caps
This is for a PAIR of front mud flap end caps for the SR5 model Toyota 4Runner. This is designed to fill in the fender gap created when the factory running boards are removed from the 1996-1998 4Runner. These are made of ABS plastic from a 3D printer. They are sanded and smoothed to hide most of the 3D printing lines. They are printed in black then chemically smoothed for strength and appearance. A coat of black plastic primer with 3 coats of flat black paint over that is used. No hardware provided. Use the factory hardware that was used to attach the running boards to the fender flares.
3rd Gen 4Runner Single CupHolder 96-02
This is a single cup holder for the 3rd gen Toyota 4Runner. It is made of ABS plastic and comes in the two factory colors which are tan “Oak” and the dark gray. The cup holder will hold any fast food cup and most beverage container sizes. If you remove the black insert then you have a much larger diameter cup holder for items like a Nalgene bottle. The cell phone slot 3.25″ across and .65″ deep which will allow for most larger cell phones on the market with a case. There is also a pen holder. This single cup holder DOES allow for almost full movement of the passenger seat front to back. You lose about 1/2″ of forward movement which is very minimal. You could push the cup holder forward to allow for full movement of the seat but that would cause the larger fast food cups to come in contact with the dash but that is also minimal. This is available for the automatic and now manual trans. Install Instructions There are 3 strips of 3m automotive adhesive already installed. This is the primary method of attachment. Make SURE the console is cleaned really well before you attach and use good force when attaching. The cup holder will not bond well if the console is not clean. 2 screws are also included to be used in the 2 screw holes. The screws are an added insurance to ensure the cup holder is secure. I would highly encourage you to use the screws. Use a small drill bit and predrill the holes once the cup holder has been stuck into place. Then use a hand held screw driver to thread the screws in. Do not use a drill because you will probably strip the screw hole. Also, do not over tighten them by hand. Turn the screw until it is snug and then stop.
1st Gen 4Runner/Surf B-Pillar Badge
This is a replacement B-Pillar badge for the 1984-1989 Toyota 4Runner. It will replace the faded clear plastic OEM badge. This is made of aircraft grade aluminum. It has 2 strips of 3M automotive adhesive on the back side for securing. Once you pop off the original OEM badge you need to clean the surface behind it so the new badge will bond well. This is available in the black/silver, red/silver, and raw metal for folks who want to do their own custom color.
TOYOTA Aluminum Universal Badge
This is a 8″x2″ machined aluminum TOYOTA retro badge. It was made to closely resemble the TOYOTA logo found on FJ40’s and other early Toyota trucks and SUVs. It has 3 recessed slots on the back for 3 long strips of 3M automotive adhesive. It will stick flush to any flat surface on any Toyota truck or SUV. It is available in black, red, and cream. The letters will have a brushed aluminum finish. More pictures are coming soon of the other colors.
2nd Gen 4Runner Double Cup Holder
This is a double cup holder for the 1990-1995 Toyota 4Runner. It is made of ABS plastic. It will hold two cups, 2 cell phones, 2 pens, and a flashlight. The black insert gives you a 3″ diameter hole to hold a large variety of drinks. The smaller hole(closer to driver) is about 2 3/4″ which holds soda cans, water bottles, and medium sized drinks nice and snug. With the black insert removed you have a 3 3/4″ hole which holds a Nalgene sports bottle and other large bottles. This comes in the factory Tan, gray, golden brown, and satin black. This attaches with 2-4 self taping screws and strips of 3M automotive adhesive. The amount of screws varies between the 2WD, 4WD, and manual tranny cup holders due to the curvatures of each console and the screws needed to make it secure.
3rd Gen TEQ Grille Badge
This is an aluminum grille badge for the 1996-2002 Toyota 4Runner. There are 3 different grille options under this product. There is the grille badge for the 96-98 grille, the 99-00 grille, and the 01-02 grille. They are very different in how they mount so be careful to order the correct one. The 96-98 and the 99-00 Grille badge will come with a backing plate that mounts to the grille surface and the aluminum badge will mount to the backing plate. No hardware is needed for the 96-98 and 99-00 grille badge. The 01-02 grille badge does not come with a backing plate but instead will come with 3 screws and washers to use the factory mounting holes. Make sure to use the provided washers with the screws. Those are used to set the depth correctly and allow the badge to sit totally flush to the grille. Make sure the grill emblem surface has been thoroughly cleaned before mounting any of the badges.Â
1st Gen 4runner Single Cup Holder
This is a cup holder for the 1st gen body 4runner. It is for the manual transmission set up ONLY. It will hold just about any fast food cup size drink with the insert installed. With the insert removed it can hold a large sports (Nalgene) bottle. There is also a pen holder and cell phone holder. The inside width of the cell phone slot is 3.25″ That should accept just about any cell phone on the market including the new IPhone6 plus. There are two avialable colors: the dark gray or black. Both colors come in a satin/flat finish. Installation: There are two strips of 3M automotive adhesive underneath the cup holder to aid in attachment. There are also 2 screw holes located at the bottom of the cell phone tray and on the bottom outer edge. Two self taping screws are provided. No drill bits or power tools are needed. Just thread the screws into the plastic with a handheld phillips screw driver. They will drill themselves into the plastic. Do NOT over tighten. You are threading into thin plastic. Thread the screws in until they are snug and stop.
1st Gen 4runner Cup Holder Console Insert
This is a single cup holder for the 84-89 Toyota 4Runner. This is made of ABS plastic by a 3D printer. It has a 3″ diameter hole which will hold most beverage containers on the market. It also has a cell phone holder slot that is 3.5″ wide which will accept just about every major phone style available. There is a notch at the bottom of the cell phone slot to allow a charging cable to be ran up from the bottom. Be aware you will need to cut a hole in the bottom on the console to be able to run the cable. There are also two holes to accept pens and a small storage compartment in the back for whatever you can stick in there. There is a countersunk hole at the bottom in case you want to screw it in. That is not a must, just a preference. Any 3/4″- 1″ coarse thread screw will work. There are also 2 strips of 3M automotive adhesive on the bottom if you want to glue it into place. This comes in a satin black finish only. Be aware that there are 4 different consoles that came on the 1st gen 4Runner and this insert will only fit in two of them(which do seem to be the more popular options). Make sure to look at the pics to make sure they match your console.
1st Gen 4Runner Double Cup Holder
This is a double cup holder for the 1st gen 4Runner. Be aware that there are two very different options. One option is for the folks with the short center console with the larger storage tray. This is NOT for the short console with rear heat. This option is only for the non heat short console. It comes with a cell phone slot, 2 pen holders, and a multi-tool/knife holder. Option two is for the later model gen 1’s with the taller console with padded armrest. This storage tray is more narrow. This option does not have the cell phone slot or knife holder due to lack of space. It does still hold two pens. These are made of ABS plastic. They will come in an unpainted gloss black finish. The gloss finish is for durability and ease of cleaning. It can be painted any color if desired.
3rd Gen 4Runner (96-02) Rear Hatch TEQ Badge
This is an aluminum rear hatch TEQ badge that will replace the factory Toyota logo. This will fit on the rear hatch of any 1996-2002 Toyota 4Runner. It matches the subtle curvature of the rear hatch of the 3rd Gen 4Runner specifically. This badge comes in black or red with a brushed aluminum raised trim. It will come with 2 recessed strips of 3M automotive decal adhesive for install. Make sure the surface is clean when installing. To remove the old factory badge you need something like a butter knife or flat head screw driver to pry it off. There are two plastic tabs that help center the factory badge that need to be fully pulled out. The glue should be off with medium force. If it does not, a blow drier or heat gun can heat it up and soften it and make removal a bit easier.
1st Gen 4Runner Single Cup Holder (rare console)
This is a single cup holder for the later years 1st Gen 4Runner. This console was not standard and is much more rare in 1st Gens. Look CLOSELY at the pictures to make sure this is the console you have before buying. This cup holder is made of ABS plastic through the use of a 3D printer. It has a slot for a cup, a phone, and 2 pens. It will come with 2 strips of 3M adhesive for attachment and one self tapping screw for added stability if desired.
3rd Gen 4Runner Rear Cargo Accessories Panel (99-02)
This is a rear cargo area accessories plate that replaces the OEM 12 volt accessory panel found on the 99-02 4Runner. This can be mounted to the 96-98 4Runner but the hole will need to be cut and a new 12VDC 10A power supply will need to be ran. This plate is made from ABS plastic by a 3D printer. There are two versions available. There is design #1 which has 2 accessory 12 volt holes/plugs, 1 OEM window switch hole (window switch not included), and one 12 volt meter display. There is also design #2 which has 3 12 volt accessory holes (no window switch hole), and a 12 volt meter. Please be aware the top right corner MUST be the 12 volt meter due to the shallow design of that accessory. Behind the plastic interior wall is a metal plate in that location and a full depth 12 volt accessory plug will not fit. The other 3 accessory locations do not have anything behind it and any 1″ accessory plug can be mounted there. You can order this as the plate only OR fully set up with all accessory plugs pre-installed with connectors and a spool of wire. Running and connecting wiring is done by the customer.
3rd Gen 4Runner Console Accessory Plate
This is an accessories panel for the 1996-2002 Toyota 4Runner. It mounts to the center console. This is made by a 3D printer from ABS plastic. This will accept OEM Toyota switches from 95-02 and some aftermarket switches. There are two options which is the 4 hole plate and the 2 holes plate. Install instructions will be provided with the packaging. Blank plug inserts can be ordered separately if you want 4 holes but only have 2 accessories so far and don’t want to have an ugly hole for a time period.
Universal 2oz. Hand Sanitizer Holder
This is a 3D printed 2oz. Hand Sanitizer bottle holder. It is made from ABS plastic. It will hold most major brands of 2oz. hand sanitizer bottles. It comes with 3 strips of 3M automotive adhesive. Some of the brands it holds are shown in picture 5 but there are more. This holder can be stuck to any flat surface in your car, shop, work space, garage, kitchen, etc. Make sure the surface you stick it to has been thoroughly cleaned first. You can order this holder with 1, 2, or 3 bottles of hand sanitizer.
1st Gen 4Runner Cup Holder (Driver Side)
This is a single cup holder that mounts onto the driver side of the console. It is a standard 3″ diameter hole which will hold the usual fast food cup, soda can, and grocery store water bottle. It will not hold the larger Hydroflasks, Yeti’s, and Nalgene bottles. Our passenger cup holder can do that. The driver side cup holder had to be smaller to account for the drivers leg and shifter levers. This attaches with 2 strips of 3M adhesive and 2 self tapping screws. It is made of ABS plastic with a 3D printer.
TOYOTA Aluminum Universal Badge
This is a 8″x2″ machined aluminum TOYOTA retro badge. It was made to closely resemble the TOYOTA logo found on FJ40’s and other early Toyota trucks and SUVs. It has 3 recessed slots on the back for 3 long strips of 3M automotive adhesive. It will stick flush to any flat surface on any Toyota truck or SUV. It is available in black, red, and cream. The letters will have a brushed aluminum finish. More pictures are coming soon of the other colors.
Aluminum TEQ Universal Badge (Round and Oval)
These are machined Aluminum TEQ badges (NOT PLASTIC) that can be mounted to any year and model Toyota/Lexus on any flat surface. It comes in 2 options. You can order the round or oval TEQ badge. Each badge comes in 3 finishes. You can get the red/silver, black/silver, and bare metal. The black/silver has a satin finish. The red/silver has a gloss finish. Just seemed to look best in those two finishes for those specific colors. The bare metal is for folks who want to paint them with your own custom color. Just do a couple heavy coats and then give 48 hours of drying time. Get some fine grit sandpaper and sand off the outer edge exposing the aluminum on the letters. The round is 3.5″ in diameter. The oval is 3.5″ tall and 5.2″ wide. These come with 3 strips of 3M automotive adhesive already installed. When installing make sure the surface is clean. Make sure you take your time to get it right. Once it’s stuck on, it does NOT want to come off.