This is a 3D printed cup holder insert that goes inside of the OEM recessed cup holder hole of the 200 Series Landcrusier and the Lexus LX570. These are 3″ diameter holes allowing for a much more secure smaller hole than the OEM holes. This will fit most beverage containers out there but not all. If drinking from something large you can simply remove the insert for a larger hole. This is made of ABS plastic. There are 3 options. Option one is for the Landcruiser Console. This option allows for the lid to close. Option 2 is for the LX570 console. This option does NOT allow the lid to close. It is the same depth as the Landcruiser insert but since the LX570 console is more shallow, you can’t close the lid. Option 3 is is also for the LX570 console but it DOES allow the lid to close. This option follows the curvature of the lid so it can close but it is more shallow. No screws, adhesive, or hardware of any kind is used. Simply insert and your done.
This is for a PAIR of front mud flap end caps for the SR5 model Toyota 4Runner. This is designed to fill in the fender gap created when the factory running boards are removed from the 1996-1998 4Runner. These are made of ABS plastic from a 3D printer. They are sanded and smoothed to hide most of the 3D printing lines. They are printed in black then chemically smoothed for strength and appearance. A coat of black plastic primer with 3 coats of flat black paint over that is used. No hardware provided. Use the factory hardware that was used to attach the running boards to the fender flares.
This is a dash mounted cell phone mount for the 91-94 80 Series Landcruiser. At full width it’s just over 4″ wide. The lower mount is 3D printed out of ABS plastic. It is held on with 2 strips of 3M automotive adhesive and 4 self taping 1/2″ screws. You can use a power drill to drill/thread the screws in BUT use a hand screwdriver to tighten them down the last little bit. Tightening down the screws with a power drill may crack the dash or strip the hole.
This is a rear double cup holder made for the 1980-1990 60 and 62 Series Landcruiser. It is made of ABS plastic through the use of a 3D printer. The finish is a satin black that can be also used as a primer for the owner to do a custom OEM color match. It can hold most beverage containers on the market. The inside diameter of the holes is 3.25″ so anything inside that diameter will fit. There are also two holes for a pen/pencil. The rear sit WILL fold all the way down without issue but will make contact with the cup holder as it folds all the way down. The contact will not damage the cup holder. It comes with 4 strips of 3M automotive adhesive and 4 self tapping screws. The adhesive is strong but I would encourage you to use the screws as well. The adhesive will do a great job holding the cup holder in place while you attach the screws. Make sure the console is clean before you stick the cup holder down.
This is a double cup holder for the 3rd row of the 1993-1997 Toyota Landcruiser. It does NOT fit the 91-92 Landcruiser due to it not having arms rests for the middle row. This cup holders hangs on the back of the 2nd row. There is no hardware or adhesive used. It does not effect the function of the middle row armrests or their movement. It can hang on either middle row seat allowing on of the middle row seats to be folded down without issue if desired. It is a very snug fit and will take some wiggling to slide it all the way down onto the middle row seat. It is designed this way to keep heavy drinks secure and prevent bouncing around. These are made of ABS plastic through the use of a 3D printer. They come in the factory tan and gray as well as a satin black. The cupholder can easily be removed at any time.
This is a single cup holder for the 1996-2004 Toyota Tacoma. There are two versions. One is for the 2WD/4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder allows for full movement of the passenger seat into the forward position. This cup holder will hold one drink, a flashlight, and 1 pen. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.
This is a single cup holder for the later years 1st Gen 4Runner. This console was not standard and is much more rare in 1st Gens. Look CLOSELY at the pictures to make sure this is the console you have before buying. This cup holder is made of ABS plastic through the use of a 3D printer. It has a slot for a cup, a phone, and 2 pens. It will come with 2 strips of 3M adhesive for attachment and one self tapping screw for added stability if desired.
This is a rear cargo area accessories plate that replaces the OEM 12 volt accessory panel found on the 99-02 4Runner. This can be mounted to the 96-98 4Runner but the hole will need to be cut and a new 12VDC 10A power supply will need to be ran. This plate is made from ABS plastic by a 3D printer. There are two versions available. There is design #1 which has 2 accessory 12 volt holes/plugs, 1 OEM window switch hole (window switch not included), and one 12 volt meter display. There is also design #2 which has 3 12 volt accessory holes (no window switch hole), and a 12 volt meter. Please be aware the top right corner MUST be the 12 volt meter due to the shallow design of that accessory. Behind the plastic interior wall is a metal plate in that location and a full depth 12 volt accessory plug will not fit. The other 3 accessory locations do not have anything behind it and any 1″ accessory plug can be mounted there. You can order this as the plate only OR fully set up with all accessory plugs pre-installed with connectors and a spool of wire. Running and connecting wiring is done by the customer.
This is an ashtray for the rear ashtray hole on the 1981-1984 40 Series Landcruiser center console. This is designed to look very similar to the OEM design but not identical. The original OEM design had numerous structural issues leading to cracking in numerous places. Those structural issues have been addressed in this design. It will still fit, look, and function like the OEM design. The hinge hardware has also been reinforced to be much more robust then the OEM slide pegs that were originally used. There are pressed fit and hidden nuts under the hinge with countersunk hardened black bolts. The original OEM metal plate spring is NOT included with this cup holder. The updated hardware gives the lid a stiffer movement which removes the need for the metal plate spring. The recessed area is still in this design to accept the OEM plate spring if you decide you want the look of it. This is made of ABS plastic with a black satin finish.
This is a 3D printed 2oz. Hand Sanitizer bottle holder. It is made from ABS plastic. It will hold most major brands of 2oz. hand sanitizer bottles. It comes with 3 strips of 3M automotive adhesive. Some of the brands it holds are shown in picture 5 but there are more. This holder can be stuck to any flat surface in your car, shop, work space, garage, kitchen, etc. Make sure the surface you stick it to has been thoroughly cleaned first. You can order this holder with 1, 2, or 3 bottles of hand sanitizer.
Be aware that there are 4 different consoles that came on the pickup and this insert will only fit one of them. Make sure to look at the pics closely to make sure they match your console. This is a single cup holder for the 84-88 Toyota Pickup. This is made of ABS plastic by a 3D printer. It has a 3″ diameter hole which will hold most beverage containers on the market. There are also two holes to accept pens and a small storage compartment in the back for whatever you can stick in there. There are 2 strips of 3M automotive adhesive on the bottom if you want to glue it into place. This comes in a satin black finish only.
This is a 3D printed double cup holder for the 1996-2002 Toyota Hilux Surf. This will work on the 4WD automatic console. This will NOT fit on the manual transmission console. That design in still in development. This cup holder is made of ABS plastic and comes in flat black only. This design one large hole with removable snap ring, one smaller hole, and a cell phone slot . The large hole with snap ring removed can accept the newest 36oz. Yeti bottle. With the snap ring in place the cup holder will hold a Nalgene and 32/40oz. Hydroflask. The smaller standard 3″ hole will accept most fast food style containers. This design will hold just about any container on the market. Be aware, this design prevents full forward movement of the passenger seat. The front 3″ of movement will be blocked by the cup holder.
Install Instructions
There are 2 strips of 3M automotive adhesive already attached to help with install. Make sure the surface attaching to is totally clean. Once stuck in place with the adhesive then you will want to use the 2 provided self-taping screws in the side and top hole. Use a hand screw driver and not a power drill so you don’t strip the hole.
This is a cup holder that inserts into the ashtray slot on the 1981-1984 Toyota Landcruiser 40 Series. This mounts to the center console and you must have the center console for this to work. It has a 3.25″ top diameter which will accept a majority of drink containers on the market. It also has a small storage cubby at the bottom for loose change or whatever else you want to store in there. This is made of ABS plastic with a satin black finish.
This will fit in the 1989-1994 Toyota pickup console. This was mostly offered in the SR5 model. This is 3D printed from ABS plastic. No hardware or tools are needed to install. This will NOT fit in the 4Runner from the same years. That is a different console and we make a different cup holder for the 4Runner console.
This is a single cup holder for the 1996-2004 Toyota Tacoma. There are two versions. One is for the 2WD/4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder allows for full movement of the passenger seat into the forward position. This cup holder will hold one drink, a flashlight, and 1 pen. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.