3rd Gen 4Runner Double CupHolder 96-02
This is a double cup holder for the 1996-2002 3rd gen Toyota 4Runner. It is made of ABS plastic and comes in the two factory colors which are tan “Oak” and the dark gray. This design is for the automatic 4WD and 2WD versions. It will NOT work on the manual transmission console. Our single cup holder design has an option for the manual tranny. The larger hole has an insert which holds large fast food cups. With the insert removed it can hold large water bottles like a Nalgene and Hydroflask bottle. The smaller cup holder can still hold large fast food type drinks snugly but can also securely hold small diameter containers like a soda can, small drink, and grocery store water bottles. There is also a cell phone slot on the passenger side that can handle almost all phones on the market. There are also two pen holders. This cup holder does NOT allow for full movement of the passenger seat. There is about 4″ of forward motion lost but the seat can still go back almost 6″ without issue. If full motion of the seat is extremely important to you then order the single cup holder which allow for that movement. Install Instructions There are 4 strips of 3m automotive adhesive already installed. Make SURE the console is cleaned really well before you attach and use good force when attaching. 2 screws are also included to be used in the 2 screw holes. The shorter silver screw goes underneath the black insert and the longer black screw goes in the lower side hole on the passenger side. Use a hand held screw driver to thread the screws in. Do not use a drill because you will probably strip the screw hole. Turn the screw until it is snug and then stop.
1995-2004 Tacoma Double Cup Holder
This is a double cup holder for the 1995-2004 Toyota Tacoma. There are two versions. One is for the 2WD and 4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder will hold two drinks, a cell phone, flashlight, and 2 pens. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength if you are adding two large drinks. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.
3rd Gen 4Runner Rear Double Cup Holder (1996-2002)
The is a rear double cup holder made for the 1996-2002 3rd Generation Toyota 4Runner. It is made of ABS plastic through the use of a 3D printer. It comes in the two factory colors of Tan and Gray. It can hold most beverage containers on the market. The inside diameter of the holes is 3″ so anything inside that diameter will fit. The flimsy factory rear cup holder will need to be removed first. There are two screws that hold the factory pull out cup holder in place. Once you pull it out you will be able to see and access them. Those 2 screws will not be reused. The new much stronger cup holder will come with 2 new longer screws. The cup holder should slide right into the hole left behind from the factory cup holder. You will need to apply force across the bottom to “click” the cup holder into place. Make SURE you here/feel the cup holder click into place. It has a locking tab underneath that will help secure it onto the console while you thread in the two screws. Remember that you are threading into plastic tabs and not metal. The screws can easily crack those tabs if you over tighten them. Get them snug and then stop turning. You can also use the 3M adhesive strip for added insurance but that is not a must.
3rd Gen 4Runner Single CupHolder 96-02
This is a single cup holder for the 3rd gen Toyota 4Runner. It is made of ABS plastic and comes in the two factory colors which are tan “Oak” and the dark gray. The cup holder will hold any fast food cup and most beverage container sizes. If you remove the black insert then you have a much larger diameter cup holder for items like a Nalgene bottle. The cell phone slot 3.25″ across and .65″ deep which will allow for most larger cell phones on the market with a case. There is also a pen holder. This single cup holder DOES allow for almost full movement of the passenger seat front to back. You lose about 1/2″ of forward movement which is very minimal. You could push the cup holder forward to allow for full movement of the seat but that would cause the larger fast food cups to come in contact with the dash but that is also minimal. This is available for the automatic and now manual trans. Install Instructions There are 3 strips of 3m automotive adhesive already installed. This is the primary method of attachment. Make SURE the console is cleaned really well before you attach and use good force when attaching. The cup holder will not bond well if the console is not clean. 2 screws are also included to be used in the 2 screw holes. The screws are an added insurance to ensure the cup holder is secure. I would highly encourage you to use the screws. Use a small drill bit and predrill the holes once the cup holder has been stuck into place. Then use a hand held screw driver to thread the screws in. Do not use a drill because you will probably strip the screw hole. Also, do not over tighten them by hand. Turn the screw until it is snug and then stop.
80/100/LX450/LX470 Rear TEQ Badge (91-07)
This is an aluminum TEQ emblem for the rear hatch of all years 80 and 100 series (LX and YOTA). It has a brushed finish on the letters and outer ring. This badge can replace the factory “sombrero” or “L” OR can be mounted to either side. There is a curvature on the back that matches the curvature of the rear hatch. The emblem can be slid left or right of the factory emblem but not up or down. To attach, you will use two strips of 3M automotive adhesive (provided and already attached) Make sure to take your time when installing because once you install, the adhesive doesn’t like to let go. Make sure the surface is clean and you use good force to adhere the emblem. Also hold it in place with good pressure for about 20 seconds to ensure a good bond. The factory emblem was installed with automotive adhesive as well and has been on therir for 17+ years so anticipate a little battle to get it off. A heat gun will help but don’t use too much heat and damage the paint. A flat head screw driver and razor blade is also helpful but be VERY careful not to gouge your paint in the process. This comes in the black/silver (satin finish) or the retro red/silver option (gloss finish).
1995-2004 Tacoma Double Cup Holder
This is a double cup holder for the 1995-2004 Toyota Tacoma. There are two versions. One is for the 2WD and 4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder will hold two drinks, a cell phone, flashlight, and 2 pens. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength if you are adding two large drinks. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.