80 Series/LX450 Double Cup Holder
2nd Gen 4Runner Double Cup Holder
This is a double cup holder for the 1990-1995 Toyota 4Runner. It is made of ABS plastic. It will hold two cups, 2 cell phones, 2 pens, and a flashlight. The black insert gives you a 3″ diameter hole to hold a large variety of drinks. The smaller hole(closer to driver) is about 2 3/4″ which holds soda cans, water bottles, and medium sized drinks nice and snug. With the black insert removed you have a 3 3/4″ hole which holds a Nalgene sports bottle and other large bottles. This comes in the factory Tan, gray, golden brown, and satin black. This attaches with 2-4 self taping screws and strips of 3M automotive adhesive. The amount of screws varies between the 2WD, 4WD, and manual tranny cup holders due to the curvatures of each console and the screws needed to make it secure.
80 Series (95-97) Dash Bezel/Cell Phone Mount
This is an accessories dash bezel for the 80 series (95-97) dash. There is only one type of bezel that accepts all the different options. This will also fit the LX450. This is made of ABS plastic and will allow you to add two more accessories like OEM and Aftermarket buttons/switches, CB mic holder, cell phone holder, single 1″ RAM ball, and a double 1″ RAM ball. If the dash came with the factory pull out single cup holder then that will need to be removed. If there is a black plastic hollow insert/cubby instead of the pull out cup holder then the insert will need to be removed and discarded. The holding tabs for the factory insert are at the top. You need to compress them to pull out the insert from the dash. Reuse the two factory screws in the dash that are behind the cover to install the bezel. The cell phone holder will come with an additional 4 screws for mounting. You can also add a plug or two if you do not have two accessory buttons yet. There is also a CB mic holder that can be placed in one of the holes. The cell phone mount, plugs/inserts, RAM Ball, and CB holder are an extra cost. The finish of the bezel and inserts are a satin black to match the other black parts on the dash.
80/100/LX450/LX470 TEQ grill badge
This machined aluminum TEQ badge mounts onto the front grille of your a 91-94 & 95-97 Toyota LandCruiser (80 series) and the 98-07 (100 series). WIll also mount to the LX450 and LX470 Lexus. I offer the badge in the retro red/silver, the black/silver, and bare aluminum for the folks who want to do there own paint color. The factory chrome “sombrero” must be removed. For the 95-02 Cruiser and LX TEQ badge the easiest way to install the emblem is to remove the entire grill and then install the emblem. This is not a must. You can use a stubby screwdriver and pliers, but you will need some patience and a cool car; NOT a hot radiator. Don’t forget to remove the backing from the 3M adhesive. You want to run the screws through the backside of the grill first. Make SURE to use the provided black washers between the screws and backside of the grill. They are for spacing purposes to get the TEQ badge perfectly flat to your grill. Once the screws are through then start each screw with a full turn but prevent the adhesive from grabbing the grill Do not tighten the screws until all of them have been started. That will ensure you get everything lined up properly. Once the screws have threaded in slightly then you can press the badge onto the grill and the adhesive will hold it nice and snug while you screw in the 3 screws. Between the adhesive and screws everything should stay nice and flush. Reinstall the grille in the same way you removed it. IF you are buying the 03-07 badge then there were no screws used on the OEM sombrero badge. Toyota only used adhesive. You will need to pry the factory badge off. Some heat and fishing line will help. There are small tabs that help center the badge so you will not be able to simply run the fishing line all the way down the back side. Once the badge and adhesive are removed, you will simply stick the new badge on using the same type of 3M adhesive. No hardware needed for the 03-07 badge and no need to remove the grill.
80 Series/LX450 Single Cup Holder
80/100/LX450/LX470 Rear TEQ Badge (91-07)
This is an aluminum TEQ emblem for the rear hatch of all years 80 and 100 series (LX and YOTA). It has a brushed finish on the letters and outer ring. This badge can replace the factory “sombrero” or “L” OR can be mounted to either side. There is a curvature on the back that matches the curvature of the rear hatch. The emblem can be slid left or right of the factory emblem but not up or down. To attach, you will use two strips of 3M automotive adhesive (provided and already attached) Make sure to take your time when installing because once you install, the adhesive doesn’t like to let go. Make sure the surface is clean and you use good force to adhere the emblem. Also hold it in place with good pressure for about 20 seconds to ensure a good bond. The factory emblem was installed with automotive adhesive as well and has been on therir for 17+ years so anticipate a little battle to get it off. A heat gun will help but don’t use too much heat and damage the paint. A flat head screw driver and razor blade is also helpful but be VERY careful not to gouge your paint in the process. This comes in the black/silver (satin finish) or the retro red/silver option (gloss finish).
