This is a double cup holder for a 91-97 Toyota LandCruiser and 96-97 Lexus LX450. It also has a cell phone holder, 2 pen holders, and a flash light holder. This comes in the factory Tan “Oak” color common to the LX450 and some Toyota LandCruisers and the Toyota Gray that is common on LandCruisers. I also offer this is the Right Hand Drive (RHD) version for the non US spec console. The black inserts are removeable to allow for larger beverage containers like a nalgene bottle. I also have an optional “small insert” that fits into the existing inserts that will allow better fitment of more narrow and tall beverage containers like insulated travle mugs, soda cans, and grocery store water bottles. This item comes with 3m automotive adhesive installed on the bottom side. You can use the adhesive strips only to mount this but I would encourage you to also use the 4 provided screws/holes for added insurance. You need to predrill the holes on the center console with a smaller bit then the diameter of the screw. If you don’t predrill the holes you risk cracking the plastic on the center console. DON’T use a powered drill to screw in the screws. You can easily over torque the screws and strip the plastic holes. Use a handheld screwdriver and stop when you get decent resistance. If you have any questions feel free to message me on here. I will get back to you within 24 hours.
This is a single cup holder with cell phone holder and a pen holder for a 91-97 Toyota LandCruiser and Lexus LX450. There are two color options. There is a factory tan color which is the “Oak” common to the LX and some Toyotas. There is also the factory dark gray color common to most LandCruisers. the black insert is removeable to allow for larger beverage containers like a nalgene bottle. There is also an optional “travel mug” insert to allow tight/stable fitment on narrow and tall beverage containers. The cupholder comes with strips of 3m automotive adhesive already installed. You need to peel off the red cover. You can install the cupholder with zero screws and only use the adhesive, but I would advise you to use the screw holes AND adhesive to guarantee the cupholder never moves on you. Screws are provided. Please pre-drill the hole with a bit smaller than the screw so you don’t risk cracking the plastic on the center console. Make sure you place in the spot you like the most because once you stick it down the adhesive doesn’t want to let go. There is about 3″ of adjustability in and out to your desired location on the center console. For any questions just send me a message on here and I will get back to you within 24 hours.
This is a rear double cup holder for the 91-97 Toyota Land Cruiser and Lexus LX450. It has a storage slot underneath that can hold sunglasses or anything else in that size range. The small circle in the front between the cup slots is for an LED flashlight (not provided). The normal hardware store/harbor freight small LED flashlight will fit in that slot. Most stores carry that size. The black inserts are removable and allow for a wide range of different types of containers. There is also an optional “Travel Mug” insert. This allows for better fitment of tall containers with a narrow bottom. You can add 1 or 2 of these to the order. The rear double cup holder comes in the factory “Oak” tan color and the dark gray. There are 2 types of attachment. The first is the the 3 large strips of 3M automotive adhesive on the backside and 2nd are 4 screw holes and provided self tapping screws. Make sure to use both forms of attachment. In regards to installation, make sure you clean the backside of the console. Simply stick the cup holder on the back of the console in your desired location. Then add the four screws with a screwdriver. Don’t use a power drill or you may strip the holes.
This is an accessories dash bezel for the 80 series (95-97) dash. There is only one type of bezel that accepts all the different options. This will also fit the LX450. This is made of ABS plastic and will allow you to add two more accessories like OEM and Aftermarket buttons/switches, CB mic holder, cell phone holder, single 1″ RAM ball, and a double 1″ RAM ball. If the dash came with the factory pull out single cup holder then that will need to be removed. If there is a black plastic hollow insert/cubby instead of the pull out cup holder then the insert will need to be removed and discarded. The holding tabs for the factory insert are at the top. You need to compress them to pull out the insert from the dash. Reuse the two factory screws in the dash that are behind the cover to install the bezel. The cell phone holder will come with an additional 4 screws for mounting. You can also add a plug or two if you do not have two accessory buttons yet. There is also a CB mic holder that can be placed in one of the holes. The cell phone mount, plugs/inserts, RAM Ball, and CB holder are an extra cost. The finish of the bezel and inserts are a satin black to match the other black parts on the dash.
This is a 3D printed 2oz. Hand Sanitizer bottle holder. It is made from ABS plastic. It will hold most major brands of 2oz. hand sanitizer bottles. It comes with 3 strips of 3M automotive adhesive. Some of the brands it holds are shown in picture 5 but there are more. This holder can be stuck to any flat surface in your car, shop, work space, garage, kitchen, etc. Make sure the surface you stick it to has been thoroughly cleaned first. You can order this holder with 1, 2, or 3 bottles of hand sanitizer.
These t-shirts are made of a very soft durable cotton from Next Level Apparel. They come in a gun metal gray color. It tends to run as a slight “slim” fit meaning it’s a little bit more snug in the shoulders and arms. They are a good long length for men but run a little snug. If you like a loose fitting shirt then I would say order one size up from what you normally where.
This is a BH3D adjustable fit mesh back hat. It’s a charcoal gray color. This hat is built Richardson and is their Type 112 hat built to last. If you spend over $100 on our website then the hat is free.
Use Coupon code “Free Hat” during checkout once you have added at least $100 of product into the cart. Also, make sure you actually add the hat into the cart first.
These are machined Aluminum TEQ badges (NOT PLASTIC) that can be mounted to any year and model Toyota/Lexus on any flat surface. It comes in 2 options. You can order the round or oval TEQ badge. Each badge comes in 3 finishes. You can get the red/silver, black/silver, and bare metal. The black/silver has a satin finish. The red/silver has a gloss finish. Just seemed to look best in those two finishes for those specific colors. The bare metal is for folks who want to paint them with your own custom color. Just do a couple heavy coats and then give 48 hours of drying time. Get some fine grit sandpaper and sand off the outer edge exposing the aluminum on the letters. The round is 3.5″ in diameter. The oval is 3.5″ tall and 5.2″ wide. These come with 3 strips of 3M automotive adhesive already installed. When installing make sure the surface is clean. Make sure you take your time to get it right. Once it’s stuck on, it does NOT want to come off.
This is an aluminum retro “Turbo” badge. This is inspired by the “Turbo” badge Toyota made in the 1980s. It can mount to any flat surface on the vehicle. Will come with 1-2 strips (depending on size) of 3M automotive adhesive to mount to the vehicle. There are 2 sizes and two color options for each size for a total of 4 options. There is the 7″ and 5″ black/silver badges. There is also the 7″ and 5″ black/silver/red badges.
These are Retro Toyota “T” logos inspired from Toyota logos used in the early 80s. Instead of chrome plastic we went with a more modern brushed aluminum. There are 2 versions. Version #1 is a bit larger at 4″ tall by 3 1/4″ wide. Versioni #2 is 3 3/8″ x 3 1/4″ wide. These are a bit larger than the original OEM badges. They both come with 2 strips of 3M automotive adhesive on back in case you want to stick it on. They will mount to any flat surface on our vehicle. They also come with screws and washers and pre-existing threaded holes in case you want to attach with screws. You do NOT need to use both forms of attachment.
This is a single cup holder that fits snugly into the square hole at the front of most 80 series LandCruisers. The LX450 came with a sub woofer in this hole so this cup holder will only fit in the 91-97 Toyota Landcruiser and not LX450. It has a slot for a cell phone that is the width of the square hole. If your phone fits in the square hole now it will fit with the cup holder installed. The cup holder diameter at the top is 3″ with a slight taper towards the bottom. If you need something larger than 3″ then you will want to buy the single or double cup holder set up that mounts on the side of the shifter console. There are also two pen holders that are tilted forward by 15 degrees to make sure the pens don’t interfere with any cup. Soda cans, water bottles, and all fast food cups all fit without issue. Anything bigger (like a Nalgene bottle) will not. These come in the factory Oak tan color and the dark gray color. These are made of ABS plastic through my 3D printer. Install is simple. Remove the 3M adhesive backing and push it into the hole until it hits bottom. It’s a snug fit so it will take a little force to get it to seat all the way into the bottom. I wanted it to be a snug fit so that if a large cup is put into it with a snug fit, it wont pull the entire insert out when you remove the cup. No screws are needed but I left the factory hole at the bottom available if you decided to run a longer screws and anchor it into place.
This is a machined aluminum retro Toyota “4 Wheel Drive” badge. It can be mounted on any flat surface of any Toyota 4×4. It is roughly 4.5″ x 3″ which is the same size as the original Toyota badge. There are 3 color options available. There is the black/silver, cream/silver, and bare aluminum. The black is a satin finish while the cream is a gloss finish. The gloss allowed the cream to stand out a bit more. The bare aluminum is for the folks that want a custom color and are willing to paint themselves. I can also do custom color combos for a couple extra dollars if you let me know what you want. Just send a message regarding your request. These come with 3 strips of 3M automotive adhesive recessed on the backside and ready to install. Make sure the surface you are sticking to if flat and clean.
This is an aluminum TEQ emblem for the rear hatch of all years 80 and 100 series (LX and YOTA). It has a brushed finish on the letters and outer ring. This badge can replace the factory “sombrero” or “L” OR can be mounted to either side. There is a curvature on the back that matches the curvature of the rear hatch. The emblem can be slid left or right of the factory emblem but not up or down. To attach, you will use two strips of 3M automotive adhesive (provided and already attached) Make sure to take your time when installing because once you install, the adhesive doesn’t like to let go. Make sure the surface is clean and you use good force to adhere the emblem. Also hold it in place with good pressure for about 20 seconds to ensure a good bond. The factory emblem was installed with automotive adhesive as well and has been on therir for 17+ years so anticipate a little battle to get it off. A heat gun will help but don’t use too much heat and damage the paint. A flat head screw driver and razor blade is also helpful but be VERY careful not to gouge your paint in the process. This comes in the black/silver (satin finish) or the retro red/silver option (gloss finish).
This machined aluminum TEQ badge mounts onto the front grille of your a 91-94 & 95-97 Toyota LandCruiser (80 series) and the 98-07 (100 series). WIll also mount to the LX450 and LX470 Lexus. I offer the badge in the retro red/silver, the black/silver, and bare aluminum for the folks who want to do there own paint color. The factory chrome “sombrero” must be removed. For the 95-02 Cruiser and LX TEQ badge the easiest way to install the emblem is to remove the entire grill and then install the emblem. This is not a must. You can use a stubby screwdriver and pliers, but you will need some patience and a cool car; NOT a hot radiator. Don’t forget to remove the backing from the 3M adhesive. You want to run the screws through the backside of the grill first. Make SURE to use the provided black washers between the screws and backside of the grill. They are for spacing purposes to get the TEQ badge perfectly flat to your grill. Once the screws are through then start each screw with a full turn but prevent the adhesive from grabbing the grill Do not tighten the screws until all of them have been started. That will ensure you get everything lined up properly. Once the screws have threaded in slightly then you can press the badge onto the grill and the adhesive will hold it nice and snug while you screw in the 3 screws. Between the adhesive and screws everything should stay nice and flush. Reinstall the grille in the same way you removed it. IF you are buying the 03-07 badge then there were no screws used on the OEM sombrero badge. Toyota only used adhesive. You will need to pry the factory badge off. Some heat and fishing line will help. There are small tabs that help center the badge so you will not be able to simply run the fishing line all the way down the back side. Once the badge and adhesive are removed, you will simply stick the new badge on using the same type of 3M adhesive. No hardware needed for the 03-07 badge and no need to remove the grill.
This is a Universal Aluminum TEQ/Diesel badge for a Toyota. The lettering is inspired by the Diesel font used by Toyota throughout the early 80s to late 90s. This is designed to mount on any flat smooth surface on the vehicle. It comes with strips of 3M automotive adhesive on back for attachment.
This is a machined aluminum badge with a satin brushed finish on the lettering. This is not a plastic replica like the OEM badge was. This badge is an exact match in size to the original factory badge and mounts with strips of 3M automotive badge/decal adhesive. No drilling of the fenders is needed. The overall length is exactly 10″ (254mm) by 1.4″(36mm) tall. This badge will fit in the factory fender location of the 1979-1983 Toyota pickup BUT it can also mount to any flat surface of any Toyota. It can be mounted on a surface like a flat tailgate of a more modern vehicle giving it that old school retro look.